d) Weathered rock mass is a very complex structure to explore due to its heteregenous and homogeneous characteristics. (i) Illustrate and discuss the differences of weathering classification system between volcanic and sedimentary rock in terms of boulder occurrence, homogeneity, discontinuity pattern and weathering period. (ii) Explain THREE (3) importance of weathering classification system in civil engineering works.

d) Weathered rock mass is a very complex structure to explore due to its heteregenous and homogeneous characteristics. (i) Illustrate and discuss the differences of weathering classification system between volcanic and sedimentary rock in terms of boulder occurrence, homogeneity, discontinuity pattern and weathering period. (ii) Explain THREE (3) importance of weathering classification system in civil engineering works.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter17: Subsoil Exploration

Section: Chapter Questions

Problem 17.15P

See similar textbooks

Similar questions

1.Write short notes on the following. (a) Contact aureole (b) Granoblastic texture (c) Porphyroclastic texture (d) Foliation (e) Grades of metamorphism 2. Distinguish between the following. (a) Slaty cleavage and gneissic textures (b) Porphyroblastic and crystalloblastic textures (c) Epizone and mesozone (d) Cataclastic and dynamic metamorphisms 3. Which of the following rock is metamorphozed to marble? (a) Granite (b) Limestone (c) Sandstone (d) Slate 4. Changes in the bulk composition of the parent rock occur primarily as a result of which of the following agent of metamorphism? (a) Pressure (b) Temperature (c) Hydrothermal fluids (d) Deformation 5. What type of metamorphism is caused by high temperature and high pressure imposed over a large volume of crust? (a) Burial (b) Contact (c) Regional (d) Cataclastic 6.Which mineral is responsible for the strong foliation in schist? (a) Mica (b) Calcite (c) Quartz (d) Chlorite
Provide generalized comments on the hardness, soundness, and durability associated with the three basic categories of rock.
1. Identifying the rock type in a basis in site investigation prior to a more detailed studyon the properties of the rock mass. This is because different types of rock will exhibitdifferent characteristics. Explain on the typical features that can be found in differenttypes of rock (igneous/sedimentary/metamorphic)?
A site is underlain by a granite having the following properties and characteristics:• Average uniaxial compressive strength of intact rock = 260 MPa• Average RQD = 80,• Average discontinuity spacing = 1.1 m• Discontinuities are tight and rough, with slightly weathered walls and lengths between 3 and 10 m• Dry• Average unit weight = 25.9 kN/m3Estimate for this granite the total RMR rating, GSI, Hoek- Brown failure criterion assuming the rock is undisturbed, intact rock deformation modulus, rock mass deformation modulus, and the rock mass Poisson’s ratio.
(b) Describe rock parameters that obtained from the following testing: (i) Seismic Velocity test (ii) Brazilian test (iii) Slake durability test (iv) Schidmt hammer test (v) Triaxial Compression Test (vi) Point load test
What properties and characteristics are used to identify a gneiss metamorphic rock? Be specific.
List FIVE factors that possibly affecting the rock testing results in the laboratory?
Relating to soil deposits, provide a definition of subsurface effective stress and total stress, and explain the relationship between the two.
Select the correct statement below with regards to bit type and the DOMINANT rock failure mechanism. a. PDC bits – shear failure; roller cone bits – compressive failure b. PDC bits – compressive failure; roller cone bits – shear failure c. There is no one dominant rock failure mechanism for PDC and roller cone bits d. PDC bits – erosion by fluid jet action of the nozzles; roller cone bits – wedging
A copper bearing host rock is blasted and found to exhibit a swell factor of 30%. What is the resulting material density in tons per loose cubic meter (LCM) if the specific gravity is 2.5?
Question 10 A 50 m run of core drilled horizontally from an underground drift allowed to recover 42 m ofrock core and 38 m of this core was in pieces longer than 100 mm. In the 4 m of recoveredrock core with pieces smaller than 100 mm, 2 meters contained fresh and sharp breaks(fractures).(a) Determine the Rock Quality Designation (RQD) value and the corresponding rock qualitydescription. (b) Describe the limitations of using RQD to evaluate rock quality and make suggestions onhow you can minimize the sources of error.
A site is underlain by a shale having the following properties and characteristics:• Average uniaxial compressive strength of intact rock = 34 MPa• Average RQD = 77,• Average discontinuity spacing = 0.5 m• Discontinuities are slightly rough, with slightly weathered walls, lengths between 3 and 10 m, and with narrow openings and no filling• Dry, with occasional localized dampness• Average unit weight = 24.0 kN/m3Estimate for this shale the total RMR rating, GSI, Hoek- Brown failure criterion assuming the rock is undisturbed, intact rock deformation modulus, rock mass deformation modulus, and the rock mass Poisson’s ratio.