Explain and Solve correct i got wrong answer Previous time D. = 0.250"D, = 0.125"*L= 6.250"If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev; Find(a) N=?(b) f=?(c) Tm=?

Cutting speed v=211 ft/minor v=211×12 =2532 in/minf=.0018 in/revD0=.250''Df=.125''L=6.250''

Answered: D. 0.250" D, = 0.125" L-6.250" If…

D. 0.250" D, = 0.125" L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev; Find (a) N=? (b) f=? (c) Tm=?

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter3: Job Planning, Benchwork, And Layout

Section3.4: Saws And Cutoff Machines

Problem 2RQ: The vertical band saw is particularly useful, as it can be used to make straight cuts as well as...

See similar textbooks

Related questions

Q: Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final…

Q: The rpm (N) of the shaft, diameter (d) =25 mm, cutting speed (v) =50 m/min is; O 39.25 O 636.9 O…

A: Given data as per question Diameter of shaft=25 mmcutting speed =50mmincalculating speed of…

Q: (b):- Calculate the total time to mill a block of aluminum with dimensions of 100 x 40 x 50 to…

Q: D.= 0.250" D, = 0.125" %3D L- 6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018…

A: Given:Do=0.250 inDi=0.125 inv=211 feet/minf=0.0018 in/rev

Q: D.= 0.250" D, = 0.125" %3D L-6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018…

A: Given:v=211 feet/minf=0.0018 in/revL=6.250 in

Q: in shaft turning Steel raw material, diameter 40 mm., length 200 mm. to obtain a lathe workpiece…

A: Given, D1 = 40 mm L1 = 200 mm D2 = 35 mm L2 = 150 mm Cutting Speed, S = 25 m/min feed rate, f = 0.2…

Q: In a slab milling operation , L_w = 200 mm table feed = 18 mm/min, diameter of cutter = 34 mm depth…

A: Given Data: The length of the slab is, Lw=200 mm. The feed rate of the table is, f=18 mm/min. The…

Q: cutting at V = 30 m/min, f 0.3 mm of cut are increased together by 20

Q: In 3-axis milling, the table feedrate is 756.00 mm/min. Using a 10mm endmill to cut the material…

Q: Determine the total machining time for a workpiece 30mm in diameter and the required length is 145…

A: Given: Initial length of the material→X=149 mm Initial Diameter of the material→D=38 mm Depth of cut…

Q: 5. An engine lathe is used to turn a cylindrical work part, cutting speed 2.4 m/s, feed 0.20 mm/rev,…

Q: thickness is HW3.A block of steel has a length L-600mm and a width W-450mm. The Machined 10mm, once…

Q: 3. A turning operation is carried out on aluminum (100 BHN), the cutting conditions are: v = 5.6…

Q: Q3 A) A shaft with 150mm in diameter and 1 m length is to be turned in an engine lathe. Cutting…

Q: The face milling cutter of D = 200 mm used to cut a block which is 200 mm = H, 1=480 mm, if f- 0.7…

A: Machine time is the ratio of length divided by cutting speed. Here, Length = length of block +…

Q: 1.10A O50 mild steel bar is being turned at 1.70 revis on a multi-tool center lathe having nine…

Q: A cylindrical work bar with 4.5 in diameter and 52 in length is chucked in an engine lathe and…

A: (a) The depth of cut is, d = 0.125 in. (b) The required feed is, f = 0.010 in/rev. (c) The cutting…

Q: A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine…

Q: Q.4 (i) Find the time required for taking a complete cut on a plate 600 × 900 mm², if the .cutting…

A: As per the bartleby policy we can solve the only first question from the multiple questions. Q.4 (i)…

Q: B/ A rectangular aluminum block is drilled at a depth of 40 mm using a drill that has two cutting…

Q: A 12" x 4" block of soft aluminum alloy (u, = 2.5 hp.min/in³) is face milled at a depth of cut of…

A: Given Data: Depth of cut DC=18inch Length of block l=12 in Breadth of block b=4 in ut of aluminium…

Q: As the cutting speed for mild steel is 100ft/min and RPM is 1000, find the diameter of the cutting…

A: Given data as per question cutting speed = 100 ft/min Speed =1000 Feed rate =0.002 in v=100…

Q: 39- An orthogonal cutting operation is being carried out under the following conditions: t0-D0,38…

A: Givent0=0.38mmtc=0.65mmwidth of cut=2.5mmV=3.5m/srake angle=6°Fc=515NFt=210Nto find:-Percentage of…

Q: H.W. The face milling cutter of D= 200 mm used to cut a block which is 200 mm = H, 1 =480 mm, if f=…

Q: b) Derive an expression for the "peak to valley" height Rt of a turned surface cut on a lathe with a…

A: As per Bartleby's policy in case of multiple questions I can only one. Please repost last one as…

Q: HW3: A block of steel has a length I. = 600 mm and a width W = 450 mm. The thickness is Machined 10…

Q: The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of…

Q: 1.10A O50 mild steel bar is being tumed at 1.70 revis on a multi-tool center lathe having nine…

Q: 3. It is required to machine a slot with length 100 mm, width 15 mm, and depth 4 mm. Calculate the…

A: Given: The length of machine slot, L = 100 mm The width of machine slot, b = 15 mm The depth of…

Q: During orthogonal cutting of mild steel with a 10° rake angle tool, the chip thickness ratio was…

A: Given, Orthogonal rake angle, α=10° Chip thickness ratio, r=0.4

Q: In a turning operation on cast iron, the nose radius on the tool = 1.5 mm, feed = 0.22 mm/rev, and…

A: Given data: Nose radius of the tool = 1.5 mm Feed = 0.22 mm/rev Speed = 1.8 m/s Need to determine…

Q: In a surface broaching process, a broach having 8 mm pitch and cut per teeth 0.01 mm is used for…

Q: In a turning operation on low carbon steel with hardness = 135 HB, the cutting speed = 180 m/min,…

Q: 5. AT-slot is to be cut in a C.I. slab 260 mm long as shown make the T-slot if the cutting speed is…

A: Given Cutting speed, v = 25 m/min Diameter, d = 20 mm Number of teeth, z = 6 Find…

Q: A part to be turned in an engine lathe must have a surface finish of 1.6 mm. The part is made of a…

Q: Write down the steps required to proof the mathematical relation for SHEAR PLANE ANGLE in Orthogonal…

Q: late the machining time to drill the flange as shown below. Take cutting speed 20 m/min, feed for 20…

A: Soln:- depth = 20 mm Number of Revolution required = depth/feed = 20/ 0.2 = 100 rev. V=…

Q: Q3 A) A shaft with 150mm in diameter and 1 m length is to be turned in an engine lathe. Cutting…

Q: D. = 0.250" D, = 0.125" L- 6.250" If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev;…

Q: 1. A turning operation is performed on a cylindrical work part whose diameter 150 mm and length 375…

Q: Q1_Tuming operation carried out on Aluminum shaft with specific energy of 0.7 N.m/mm. Cutting speed…

A: As per our guidelines we are supposed to do only first question, if more than one question asked,…

Q: 6. Compute for the necessary stroke per minute on 8 inches copper if it has 100 fpm as its cutting…

Question

Explain and Solve correct i got wrong answer Previous time

D. = 0.250"
D, = 0.125"*
L= 6.250"
If Cutting speed v=211 FPM (feet per minute) and f= 0.0018 in/rev; Find
(a) N=?
(b) f=?
(c) Tm=?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

in shaft turning Steel raw material, diameter 40 mm., length 200 mm. to obtain a lathe workpiece diameter 35 mm., length 150 mm, as shown in the figure, with a cutting speed of 25 m/min and a rough-cutting feed rate (f) 0.2 mm/rev. The feed rate for finishing (f) 0.1 mm per revolution determines a depth for rough turning of not more than 1 mm and a depth for finishing of not more than 0.5 mm. Find 1) the speed of rotation used per minute. 2) Details of turning Such as how many rounds of rough turning, how many rounds of fine turning? 3) From the available data Find the approximate turning time in minutes.
An orthogonal cutting operation is being carried out under the following conditions: t0=0.38 mm, tc=0.65 mm, width of the cut= 2.5 mm, V=3.5 m/s, rake angle=6°, Fc= 515 N, and Ft=210 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
In the machining operation with orthogonal cutting, the cutting plane angle is 9.5°, the cutting depth 0.4 mm, chip thickness 2.9 mm, cutting width 3.1 mm, shear strength 185 MPa in the process; a) Find the rake angle (α). b) Find the shear deformation (γ). c) Find the shear force. (Note: The shear force is 1.4 times the thrust.)
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
2 1.57 Show that, for the same shear angle, there are two rake angles that give the same cutting ratio.
A cylindrical workpiece has a 14.0 in diameter and has 30 in long. It is to be turned in an engine lathe at the following cutting conditions: cutting speed = 400 ft/min, feed = 0.015 in/rev, and depth of cut = 0.150 in. Determine the time to complete one turning pass if the approach and overtravel allowances are each 0.25 in (total = 0.50 in). Note: 1 ft = 12 in
21.53 An orthogonal cutting operation is being carried out under the following conditions: to = 0.1 mm, tc = 0.2 mm, width of cut = 4 mm, V = 3 m/s, rake angle = 10°, Fc = 500 N, and Ft = 200 N. Calculate the percentage of the total energy that is dissipated in the shear plane.
Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.
The following data is applicable for a turning operation. The length of job is 900 mm, diameter of job is 200 mm, feed rate is 0.25 mm/rev and optimum cutting speed is 300 m/min. The machining time (in min) is ___. A. 7.539 B. 7.90 C. 8.25 D. 9.00
Manufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mm
During orthogonal cutting of mild steel with a 10° rake angle tool, the chip thickness ratio was obtained as 0.4 .Calaculate the shear angle.