Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm

Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.3: Machining Operations On The Lathe

Problem 5RQ: Calculate spindle RPM and machining time for cutting a 1.5" diameter 4" long at 225 SFPM using a...

See similar textbooks

Similar questions

The vertical band saw is particularly useful, as it can be used to make straight cuts as well as ______________.
Machining time required reduce a mild steel rod of diameter 60mm, initial length (L) 125mm to final length (L1) 120mm to 58 mm by turning a carbide insert. If the approach length and over run length are 5 mm and 1 mm respectively, take Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Find the machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by using a carbide insert. If the approach length and over run length is taken as 5 mm, Cutting speed as 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm
Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.
(j) In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 250 m/min, feed = 0.3 mm/rev, and depth of cut = 8 mm. How much power will the lathe draw in performing this operation if its mechanical efficiency = 95%. Use Table below to obtain the appropriate specific energy value.
A hole of 30 mm diameter and 75 mm depth is to be drilled. The suggested feed is 1.3 mm per rev and the cutting speed is 62 m/ min. assuming tool approach and tool overtravel as 6 mm, determine: i. spindle rpm ii. feed speed iii. cutting time iv. material removal rate
5.) Calculate the machining time required to reduce from 60mm diameter shaft to 50mm diameter, for a length of 1500mm with depth of cut 2mm for rough cut and 1mm for finish cut. Cutting speed and feed may be assumed as 30m/min and 0.5mm/rev respectively.
In a slab milling operation , L_w = 200 mm table feed = 18 mm/min, diameter of cutter = 34 mm depth of cut = 2 mm. Considering approach and overtravel to be same. The milling time in min will be?
In orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.
Q#2 “Milling is an intermitted cutting operation”. Explain it.
Find the machining time, in seconds, and the rate of material removing in mmA3;sec for a turning operation having the following information: 1- Wp diameter is 80mm, 2- the length is 0.12m, 3- the cutting speed is 80m/min, 4- feed i50.5 mm/rev and 5- the depth of cut is 0.002m.
During orthogonal cutting of mild steel with a 10° rake angle tool, the chip thickness ratio was obtained as 0.4 .Calaculate the shear angle.