DA double-acting duplex pump, 2.5 in rod, 20 in stroke, is to be operated at 60 strokes/min. For drilling down to 10000 ft. The maximum available pump hydraulic horsepower is 1360 HP with an efficiency of 90 %. For optimum hydraulics, the pump delivery pressure is recommended to be 3423 psi. Determine the liner size to be used.

DA double-acting duplex pump, 2.5 in rod, 20 in stroke, is to be operated at 60 strokes/min. For drilling down to 10000 ft. The maximum available pump hydraulic horsepower is 1360 HP with an efficiency of 90 %. For optimum hydraulics, the pump delivery pressure is recommended to be 3423 psi. Determine the liner size to be used.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piston PDP has a 5-in diameter and a 2-in stroke andoperates at 750 r/min with 92 percent volumetric effi ciency.(a) What is its delivery, in gal/min? (b) If the pump deliversSAE 10W oil at 20°C against a head of 50 ft, what horsepoweris required when the overall effi ciency is 84 percent?
A two-lobe rotary positive-displacement pump, similar to that of Fig., moves 0.45 cm3 of SAE 30 motor oil in each lobe volume Vlobe, as sketched. Calculate the volume flow rate of oil for the case where n. = 900 rpm.
Fluid Mechanics. plz, solve all the parts from a , b and c Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
Suppose that the axial-flow pump of Fig. with D =18 in, runs at 1800 r/min. (a) Could it efficiently pump25,000 gal/min of water? (b) If so, what head would result?(c) If a head of 120 ft is desired, what values of D and nwould be better?
Solve problem 2 (Textbook, p. 230). This is a case example how to use the characteristic curve of a pump to find the operation point of a piping installation. You can find the solution graphically, iteratively (if you want to fit the curve of Fig. P4.2 with an equation) or using trial and error (my recommendation). 2. Pump and pipeline—M . The head/discharge curve of a centrifugal pump is shown in Fig. P4.2. The exit of the pump is connected to 1,000 ft of nominal 2-in. diameter horizontal pipe (D = 2.067 in.). What flow rate (ft^3/s) of water can be expected? Assume atmospheric pressure at the pump inlet and pipe exit, and take fF = 0.00475.
Suppose the pump of Fig. is situated between two large water tanks with their free surfaces open to the atmosphere. Explain qualitatively what would happen to the pump performance curve if a valve in the piping system were changed from 100 percent open to 50 percent open, all else being equal. Repeat for the system curve. What would happen to the operating point—would the volume flow rate at the operating point decrease, increase, or remain the same? Indicate the change on a qualitative plot of H versus V. , and discuss.
For a centrifugal pump of impeller diameter D rotating at N to develop a head of H and discharge Q, what would be the new head developed by a similar pump if we double the impeller diameter to 2D at constant impeller speed?
A centrifugal pump discharging 10 lps against 25 m of head and operating with an efficiency of 60% requires 4.1 kW at 1000 rpm. What is the theoretical discharge if the speed is increased to 1500 rpm assuming the efficiency remains constant? What is the theoretical head and kW at 1500 rpm?.
The plunger diameter of a single acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10,3 m of water, and the water level in the sump is 3 m below the pump cylinder axis. 2.1 Find the maximum allowable speed to operate the pump 2.2 What power is expected in overcoming friction at this speed, take f=0.01
A pump must be designed to deliver 6 m3/s of water againsta head of 28 m. The specified shaft speed is 20 r/s. Whattype of pump do you recommend?
Ex.2: In a test of the centrifugal pump shown in Fig. below, the following data are taken: py =100 mmHg (vacuum) and pz = 500 mmHg (gage). The pipe diameters are D1 = 12 cm and Dz = 5 cm. The flow rate is 180 gal/min of light oil (SG =0.91). Estimate (a) the head developed, in meters, and (b) the input power required at 75 percent efficiency. — -—