Decide whether each of these statements is TRUE (T) or FALSE (F). For the following rung of a ladder program, there is an output when: Input 1 Input 2 Output NOI (i) Just input 1 is activated. Which option BEST describes the two statements? A (i) T (ii) T B (i) T (ii) F (ii) Just input 2 is activated. C (i) F (ii) T D (i) F (ii) F

Decide whether each of these statements is TRUE (T) or FALSE (F). For the following rung of a ladder program, there is an output when: Input 1 Input 2 Output NOI (i) Just input 1 is activated. Which option BEST describes the two statements? A (i) T (ii) T B (i) T (ii) F (ii) Just input 2 is activated. C (i) F (ii) T D (i) F (ii) F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using signavio or any PBM tools and must Use pool and lane and object. Model the following business process at a supplier. After a supplier notifies a retailer of the approval of a purchase order, the supplier can receive an order confirmation, an order change, or an order cancelation from the retailer. It may happen that no response is received at all. If no response is received after 48 h, or if an order cancelation is received, the supplier will cancel the order. If an order confirmation is received within 48 h, the supplier will process the order normally. If an order change is received within 48 h, the supplier will update the order and ask again the retailer for confirmation. The retailer is allowed to change an order at most three times. Afterwards, the supplier will automatically cancel the order.
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 Use your knowledge of differentiation to sketch the velocity-time graph, clearly marking the critical points. Using the graph sketched in (a) above, estimate the velocity when t = 1.5 s Calculate the velocity of the function when t = 1.5 s by substituting to the velocity function. Compare this value to the value you estimated in b above.
Can you walk me through using STK to verify this result? I have STK 12 for referance.
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
On EXCEL VBA, please post code that solves for the following silver-meal heuristic problem: Holding cost is $.25, setup cost is $200 and demand is (200, 220, 240, 260, 280, 300) Please output the timing and quantities of planned order releases
Suppose your CFD code can handle nonelementary blocks. Combine as many blocks of Fig. as you can. The only restriction is that in any one block, the number of i-intervals and the number of j-intervals must be constants. Show that you can create a structured grid with only three nonelementary blocks. Renumber all the blocks and indicate how many i- and j-intervals are contained in each block. Add up all the cells and verify that the total number of cells does not change.
are these the correct equations for Q? Node 1:inflow Node 2=Qa+Qb+Qc+Qd Node 3= Qd+Qd2+Qk+Qj Node 4= Qd2+Qi+Qg+Ql Node 5= Ql+Qm+Qn+Qq Node 6:Qq+Qp+Qr+qs Node 7:Qb+Qe+Qj+Qh Node 8:Qc+Qk+Qg Node 9: Qf+Qf1+Qe Node 9a:inflow Node 10Qf1+Qi+Qh Node 11: inflow Node 12:Qo+Qm+Qp Node 13:outflow
The following tools / resources may be useful for you to complete the assignment:a. Chatgpt (You may use it to learn Matlab coding or any other computer language. An example is given here: https://shareg.pt/mXHGne9 ). Please take note that code generated by chatgpt can be directly copied and pasted.b. Matlabi) Useful cheat sheet (https://n.ethz.ch/~marcokre/download/ML-CheatSheet.pdf)ii) Getting started with Matlab (https://matlabacademy.mathworks.com/en/details/gettingstarted )iii) Getting 30-day Matlab trial license (https://www.mathworks.com/campaigns/products/trials.html ) iv) Polyfit (https://www.mathworks.com/help/matlab/ref/polyfit.html )v) Exponential Fit (https://www.mathworks.com/matlabcentral/answers/91159-how-do-i-fit-an-exponential-curve-to-my-data)c. PlotDigitizer (https://plotdigitizer.sourceforge.net/ ) or a free online app that does not requires installation (https://plotdigitizer.com/app )You may use your own engineering judgement to make any assumptions on any…
Do not do the matlab part
MATLAB support with the following:
Statics Please show step by step solution please