Q1-A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall as shown in Figure. The ladder is prevented from slipping by a string OD and the tension force in the string is 50 N, and the reactions at A and B are 1.3 kN and 433 N respectively. Find the mass of the man. Fig. (1) 250 N e 30% 2m

Q1-A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a wall as shown in Figure. The ladder is prevented from slipping by a string OD and the tension force in the string is 50 N, and the reactions at A and B are 1.3 kN and 433 N respectively. Find the mass of the man. Fig. (1) 250 N e 30% 2m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.14P: A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae=...

See similar textbooks

Similar questions

The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
.15 A hitch-mounted bicycle rack is designed to carry up to four 30-lb bikes mounted on and strapped to two arms Gil (sec bike loads in the figure part a) The rack is attached to the vehicle at A and is assumed to be like a cant silkier beam A BCDGII (figure part b) The light of fixed segment AB is U = 10 lb. centered 9 in. from A (see figure part b) and the rest of the rack highs W2 = 40 lb. centered 19 in. from A. Segment ABCDG is a steel tube o(2 X 2 in. with a thickness I = 118 in. Segment BCDGII pivots about a bolt at B with a diameter d1 = 0.25 in. to allow access to the rear of the vehicle without removing the hitch rack. When in use, the rack is secured in an upright posit ion by a pin C(diameter o( pin d, = 5116 in.) (see phoo and figure part C). The of returning effect of the bikes on the rack is resisted by a force couple F h at BC. (a) Find the support reactions at A for the fully loaded rack. (b) Find forces in the bolt at B and the pin at C. (c) Find average shear stresses in both the bolt at Band the pin at C. (d) Find average bearing stresses o, in the bolt at B and the pin at C.
Find the support reacions and joint force of the construction shown on the figure, if; P=12 kN q=9 kN/m M=12 kN and L=2 m
A horizontal board weighing Wb = 600 N is hinged to a vertical wall. A personweighing Wp = 400 N stands at the end of the board 5 m from the wall. A rope is attached to theboard at a point 3 m from the wall and makes an angle of θ = 40° with theboard. Determine the tension (T) in the rope
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure, choose the alternatives that are true. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position. True or false?
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N Which option is right? a) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position or b) if the plate had a weight of 332N (applied vertically downwards in the center of the plate), the reaction Dy on the plate should be vertical downwards so that the plate still remained in balance in that position
A cylinder rests on a bar and a wall in the way indicated in the figure. The cylinder weighs 500 kgf and the bar 100 kgf. If all surfaces are smooth, determine the reactions at supports A and B of the bar.