Which of the following is not considered as a lower pair

Q: Answer a) and b) only

A:

Q: -bide and ste exponent of 0.

A:

Q: What will be the value of F,? 10 kN 5 kN + F1 F2

A: Resolve the other 3 components in terms of force F1. The 10 kN along the F1 is = (10 x cos90) = 0…

Q: Number 3

A: To find change in enthalpy

Q: Differentiate y = In- 1-x 3

A:

Q: 04C) Cable reaction force is the cable and acts .. . the object. a. perpendicular to, away from O b.…

A:

Q: Sommerfeld number of the bearing

A: Given;A hydrodynamic  journal bearing is subjected toLoad= 2000 NRotational speed=2000 rpm bearing…

Q: To find the true shape of the section, it must be projected on a plane parallel to the Profile plane…

A: A profile plane is a third plane that is perpendicular to both vertical and horizontal planes and…

Q: Hi please recheck the answer for V because it is incorrect,

A:

Q: Write F if True and T if False. Lithosphere is also called Earth's crust

A: Answer: The given statement is True-F.

Q: What does the moment of the force measure

A: Given data What does the moment of the force measure..??

Q: A wire of length 50 is to be cut into two pieces, one peing bent to form a square and the other to…

A: Given:Length of wire,L=50m(unit taken as metere as not specified)Now .Let the length of square…

Q: A B - 3 ft - 6 ft - 3 ft 2 in. 6 in. 2 in. I in. in.

A:

Q: Breaking an Xline: a. Creates a line and a ray b. Creates two rays c. Converts the Xline to polyline…

A: In AutoCAD software, XLINE is a command which is used to draw a line of infinite length. Generally,…

Q: A B (1 E F (Enter only the values in the boxes by referring the unit given in bracket.) D The value…

A:

Q: 1+154 mm 2-234 mm 3+114 mm B-15mm 28 kN |Yo

A: Given that, P=2.8 kNd=15 mm,b1=154 mm,b2=234 mm,b3=114 mm, For the given beam system the force…

Q: sure difference (Pa) between points A and B.

A: Given: To determine: The pressure difference between points A and B

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: x= ky² 20 in. y = kx²

A:

Q: 3. 2 Fig. (2)

A: For solution refer below images.

Q: or F-101 N and (a) -29°3-21° and (b) 9-25°,3-36⁰ answers:

A: Solution-  Given data- F =101 N                     θ =29º   β =21º                     θ =25º β =…

Q: how to get the -y theo

A:

Q: ke angle is 0°. The minimum value of sh

A:

Q: what is the area of A1

A:

Q: The cosine law can be used when two ?angles are already known False

A: To determine whether the given statement is TRUE or FALSE.

Q: figure below. Show that a c

A:

Q: non exact .3

A:

Q: X -2 ft- F B 2 ft F X 2 ft

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: The rate of change of shear force with respect to the distance is called as Bending Moment. Select…

A: The rate of change of the bending moment with respect to the distance is called shear force.

Q: y 1 in. 3 in. -3 in.-

A: Area of the triangle, A1=1/2(3)6=9in2 Area of the square, A2=3(3)=9 in2 Area of the quarter circle,…

Q: Which of the following is the ?horizontal view of the figure

A: Horizontal plane of projection is the plane onto which the Top View of the multi-view drawing is…

Q: Which of the above mentioned values are correct for the value of n?

A:

Q: Which one(s) of the following statements is true for limiting positions? Select all that apply.

A: In the four-bar mechanisms, the limiting positions cannot always be avoided. Hence statement (a) is…

Q: Radius of mohr circle

A:

Q: What point is I34 ?

A:

Q: Figure Qte

A:

Q: The part denoted by number 1 is the

A: According to the diagram provided in the question. It is cooling system of an automobile engine. The…

Q: Newton-meter is the international unit for a moment of a force. Select one: True False

A: Moment of force also called torque is formulated as  T= F * r  Where F is force applied , r is…

Q: Which of the following is the right .4 ?one

A: This question is based on the concept of dry bulb temperature and wet bulb temperature from…

Q: A rod consists of two parts that are made

A: Kindly refer attached files.

Q: Which of the following statement is correct Select one:

A: The given question consist friction on various types of surafaces.

Q: Draw the isomtre

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: e of 5 mm. TI d opposite to

A:

Q: prove that relationship is correct -+ 2ax

A: GIVEN THAT:  Prove v2-vo2=2ax                                    v2=Final velocity…

Q: What is the Vertical Reaction at B in kips

A: The provided beam is an indeterminate beam since the number of reactions are more than the number of…

Q: e internal force exp

A: FCE = 11.75kN

Q: The power output of

A: Given; Steam enters an adiabatic turbine operating at steady state with an;Enthalpy of,H=3251.0…

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.