Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in the two materials must not exceed 50 MN/m2 and 100 MN/m2 respectively.

Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in the two materials must not exceed 50 MN/m2 and 100 MN/m2 respectively.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
. Define the terms shear stress and shear strain, illustrating your answer by means of a simple sketch. Two circular bars, one of brass and the other of steel, are to be loaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) in single shear, (b) in double shear, if the shear stress in'the two materials must not exceed 50 MN/m 2 and 100 MN/m z respectively. [27.6, 19.5, 19.5, 13.8 ram.] Can you please show a full solution explaining what * means if you are using it thanks
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 3: A steel wire 10 m long, hanging vertically supports a tensile load of 2 kN. 1. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Neglect the weight of the rod. 2. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Consider the weight of the bar and = 7,850 kg/m3
Engineering Mechanics (Upvote will be given. Please write the complete solutions and FBDs Legibly. No long explanation needed. Solve in 3 decimal places.) Based on the problem and solution given (see the attached solution) , determine the shear stress in the grain of the timber column shown in the figure. (See the attached image)
STRENGTH OF MATERIALS. Please show the complete solutions. Rate will be given. Answer in 3 decimal places! The plate shown is fastened to the fixed member by eight 16-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 80 MPa. If P = 8200 N, what is the maximum and minimum shearing stress developed in the rivet.
Please show intermediate steps including free body diagrams, equations used, and problemsetup so that your approach can be followed. A nylon thread is subjected to a 2-lb tension force. Knowing that E = 0.5 x 10^6psi and that the maximum allowable normal stress is 6 ksi,determine (a) the required diameter of the thread, (b) the corresponding percent increase inthe length of the thread.
In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in the cables are tightened until the stress in the cables reaches 60000psi. If the working compressive stress for the wood is 216psi. Determine the smallest permissible diameter of the pole.___________inches in 2 decimal places. Take note: Write it on a paper, hand written showing answer. Thanks
A rectangular steel block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in the z direction. The block is subjected to a triaxial loading of three resultant forces as follows: 70 kips compression in the x direction, 55 kips tension in the y direction, and 48 kips tension in the z direction. If ν = 1/3 and E = 29 x 106 psi, ( a ) determine the single resultant load in the z direction that would produce the same deformation in x direction as the original loadings, ( b ) determine the single resultant load in the y direction that would produce the same deformation in z direction as the original loadings, and ( c ) determine the single resultant load in the x direction that would produce the same deformation in y direction as the original loadings.
In ASTM D245, what is the length of time for duration of load assumed for strength calculations? How does changing this duration affect the allowable stress?
A metal specimen with 20 mm diameter and 100 mm gauge length is loadedelastically with 5 kN and elongates 0.8 mm. Its diameter under this load is 19.95 mm. Calculate:a) the Bulk Modulus, Kb) the Shear Modulus, G