Load (kN) Elongation (mm) Please state your assumptions and show all your work clearly. 0.0125 0.0375 A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress-strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 7.0 21.0 36.0 50.0 53.0 53.0 54.0 1. 0.0625 0.0875 þ.125 0.2 0.5 1.0 2.5 7.0 75.0 90.0 97.0 87.8 83.3 10.0 0.001 mm/mm. 11.5

Load (kN) Elongation (mm) Please state your assumptions and show all your work clearly. 0.0125 0.0375 A tension test was performed on a steel specimen having an original diameter of 12.5 mm and gauge length of 50 mm. The data is listed in the table. Plot the stress-strain diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the rupture stress. Use a scale of 25 mm = 140 MPa and 25 mm = 0.05 mm/mm. Redraw the elastic region, using the same stress scale but a strain scale of 25 mm = 7.0 21.0 36.0 50.0 53.0 53.0 54.0 1. 0.0625 0.0875 þ.125 0.2 0.5 1.0 2.5 7.0 75.0 90.0 97.0 87.8 83.3 10.0 0.001 mm/mm. 11.5

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Please show intermediate steps including free body diagrams, equations used, and problemsetup so that your approach can be followed. A nylon thread is subjected to a 2-lb tension force. Knowing that E = 0.5 x 10^6psi and that the maximum allowable normal stress is 6 ksi,determine (a) the required diameter of the thread, (b) the corresponding percent increase inthe length of the thread.
Nicole took a steel rod, 15.08-mm in diameter, and held snugly (but without any initial stress) between rigid walls as shown in the figures. Assuming that the steel rod has a CLTE is 12.4 ×10−6mm/mm∘C and E = 200GPa. 1) Calculate the temperature drop at which the average shear stress in the 11.78-mm diameter bolt becomes 46.387MPa.2) Calculate the normal stress on the rod3) Based on figure (a). What is the average bearing stress between the washer (21.84 mm diameter) and the wall (thickness: 19.89mm) 4) What is the average bearing stress between the bolt and clevis with a thickness of 14.34mm?
SHOW COMPLETE ANSWER AND ILLUSTRATION FINAL ANSWER IN 3 DECIMAL PLACES Problem 3: A steel wire 10 m long, hanging vertically supports a tensile load of 2 kN. 1. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Neglect the weight of the rod. 2. Determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 5 mm. Use E = 200 GPa. Consider the weight of the bar and = 7,850 kg/m3
Define the terms shear stress and shear strain, illustrating your answer by meansof a simple sketch. Two circular bars, one of brass and the other of steel, are to beloaded by a shear load of 30 kN. Determine the necessary diameter of the bars (a) insingle shear, (b) in double shear, if the shear stress in the two materials must notexceed 50 MN/m2and 100 MN/m2respectively.
Engineering Mechanics (Upvote will be given. Please write the complete solutions and FBDs Legibly. No long explanation needed. Solve in 3 decimal places.) Based on the problem and solution given (see the attached solution) , determine the shear stress in the grain of the timber column shown in the figure. (See the attached image)
Calculate the steel ratio that will produce a tension-controlled failure if compressivestrength f’c = 28 MPa and steel yield strength fy the answer is 0.02167 but i don't know how to solve it please help
calculate the corresponding depth uniform stress block in a reinforce concrete beam 42*10 deep reinforce with bars 20-mm in a diameter enclosed with 10-mm dia stirrups when the tensile steel strain is 0.008 and concrete compression strain 0.003. f'c = 22 Mpa. Express your anser in 2 decimal places only in mm.
Determine the required diameter (in inches) of rod ACif the allowable normal stress is 26.6 ksi and P = 11.32 kips. Round off the final answer to four decimal places.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
Two wooden boards are joined by cutting and gluing them together along the plane shownin the illustration. The boards have cross-sectional dimensions of 3.5” by ¾” and are subjectedto an axial tension, P, of 1870 lb.a) Determine the normal and shear stresses acting on the glued joint if  = 20o.b) For what joint angle, , will the shear stress on the glued joint be equal (in magnitude) totwice the normal stress on the joint?
Calculate the maximum stress in a 5mm thick steel plate with an 18 mm diameter round hole, given h gross = 12cm and the tensile load is 8.5 kN. (Submit answer in Mpa) Please solve carefully, Specifically Area calculation. Thanks