2. The compound bar given in figure, composed of the three segments shown, is initially stress free.Compute the stress in each material if the temperature drops 25 °C. Assume that the walls do notyield and use the following data:A (mm?)a (1°C)E (GPa)Bronze segment200019.0 x 10-683Aluminum segment140023.0 x 10-670Steel segment80011.7 x 10-6200800 mm500 mm–+400 mm→AluminumSteelBronze

Given above data temperature of material drops 25°C

"he compound bar given in figure, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25 °C. Assume that the walls do not rield and use the following data: A (mm2) a (1°C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segment 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10-6 200 -800 mm - -500 mm- +400 mm→ Aluminum Steel Bronze

"he compound bar given in figure, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25 °C. Assume that the walls do not rield and use the following data: A (mm2) a (1°C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segment 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10-6 200 -800 mm - -500 mm- +400 mm→ Aluminum Steel Bronze

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
How does a tensile stress differ from a compressive stress?
3 DECIMAL PLACES 1. what is the axial stress in the bronze rod (MPa)? first pic 2. what is the maximum tangential stress (MPa) if the internal pressure is 1.8 MPa and the wall thickness is 13mm? second pic
Determine stress value
A steel flat 10 cm wide and 2 cm thick is bent into a circular arc of 50m radius.Find the maximum intensity of stress induced. Take E = 2.05 * 10 ^ 5 N/mm².
Define Volume Change Due to Deviator Stress
Define the following:a. Proportional limitb. Elastic limitc. Yield stress
The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of –20°C, there is a gap of 2.2 mm, as shown below. Determine the temperature in °F at which the compressive stress in the bar will be 30 MPa. Use α =18(10)-6/°C and E = 80 GPa. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
Determine normal stress across plane passing through 50 degree to the plane 100 N/mm2
A steel pipe of length L = 4.0 ft, outside diameter = 6.0 in., and inside diameter = 4.5 in. is compressed by an axial force P kips. The material has modulus of elasticity E = 30,000 ksi and Poisson’s ratio υ = 0.30. Determine the following quantities for the pipe: (a) the shortening, (b) the lateral strain (c) the increase in the outer diameter and the increase in the inner diameter, and (d) the increase in the wall thickness. (Where P is equal to 51kips)
Determine the safe wall thickness of a 35 inches steel tank with internal pressure of 8.02 Mpa. The yield stress of material is at 300 Mpa. The factor of safety to use is 2.5. d. 21.6 mm c. 28.4 mm b. 26.8 mm a. 29.7 mm
Discuss Computation of Effective Stresses