der keyed to shaft. When the clutch is at rest, each shoe is pulled against a stop by a spring so as to leave a radial Jv. A centrifugal clutch has four shoes which slide If the internal diameter of the rim is 400 mm, the mass of each shoe is 8 kg, the stiffness of the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the driven clearance of 5 mm between the shoe and the rim. The pull exerted by the spring is then 500 N. The each spring is 50 N/mm and the coefficient of friction between the shoe and the rim is 0.3; find the mass centre of the shoe is 160 mm from the axis of the clutch. power transmitted by the clutch at 500 r.p.m.

der keyed to shaft. When the clutch is at rest, each shoe is pulled against a stop by a spring so as to leave a radial Jv. A centrifugal clutch has four shoes which slide If the internal diameter of the rim is 400 mm, the mass of each shoe is 8 kg, the stiffness of the driving shaft and make contact with the internal cylindrical surface of a rim keyed to the driven clearance of 5 mm between the shoe and the rim. The pull exerted by the spring is then 500 N. The each spring is 50 N/mm and the coefficient of friction between the shoe and the rim is 0.3; find the mass centre of the shoe is 160 mm from the axis of the clutch. power transmitted by the clutch at 500 r.p.m.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.77P: The cone clutch transmits the torque C through a conical friction surface with cone angle . The...

See similar textbooks

Similar questions

The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a mean radius of 75 mm. The static and kinetic coefficients of friction between the gear and the screw are 0.12 and 0.06, respectively. The input torque applied to the screw is C0=10Nm. Assuming constant speed operation, determine the output torque C1 acting on the gear.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The 320-lb homogeneous spool is placed on the inclined surface. Determine the vertical force P that is required to keep the spool in the position shown. Assume that there is enough friction to prevent slipping at A.
The collar bearing carries the axial load P = 400 N. Assuming uniform pressure between the collar and the horizontal surface, determine the couple C required to start the shaft turning. Use s=0.15 for the coefficient of static friction.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
Can the uniform bar of weight W remain at rest in the position shown?
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The spring is connected to a rope that passes over the cylindrical surface and is attached to corner A of the rocker. The spring has a stiffness k and is undeformed when =0. When the weight W is suspended from A, the equilibrium position of the rocker is =30. Determine if this equilibrium position is stable. Neglect the weight of the rocker.
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?