: Derive the two Tds relations from the energy balance. a. The first Tds relation and the second Tds relation. b. Derive the entropy change between two states 1 and 2 for solids in terms of the specific heat. c. For an isentropic process, derive the relationship between temperatures of the two states for solid. d. What are the entropy changes from the Tds relations if ideal gases are

: Derive the two Tds relations from the energy balance. a. The first Tds relation and the second Tds relation. b. Derive the entropy change between two states 1 and 2 for solids in terms of the specific heat. c. For an isentropic process, derive the relationship between temperatures of the two states for solid. d. What are the entropy changes from the Tds relations if ideal gases are

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Vapor Nozzle Due to a failure, ammonia in a large container overheats to 14 bar, 300°C. At this state, a small crack opens in the container that acts as a nozzle. The outside environment is at 1bar, 25°C, and the mass flow rate of ammonia is 10 kg/s. Assume negligible nozzle inlet velocity and adiabatic reversible flow. Determine the exit velocity, and the exit cross section.
A reheat cycle with two stages of reheating is executed with steam expanding initially from 25 MPa and 600 °C. The two reheater pressures are 4 MPa and 1 MPa, and the steam leaves each reheater at 600 °C. Condensation occurs at 40°C. For 1 kg/s of steam, what is QA in kW? Remember, 1. For values taken from the steam tables: Use them as is, do not round off. 2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places. 3. Use the steam tables provided
The value of enthalpy at point 1 is ( hi2 ?) The value of enthalpy at point 3 is (h3?) The value of enthalpy at point 4 is (h4?) The value of steam mass flow rate in kg/s is The rate of heat supplied is
Steam at 4.56MPa, 300C undergoes an isochoric process its dryness faction becomes 80% at 0.6MPa. Determine dU, dS, Wsf, Q, and dH.
Three kg of steam has an initial enthalpy of 7200 kJ at 0.145 MPa. Isentropic compression gives a final pressure of 0.29 MPa. Find (a) the initial and final temperatures and (b) the work of a steady and nonflow processes. Ans. (a) 110.4°C, 132.4°C; (c) –288.5 kJ, –325.8 kJ.
Draw a schematic diagram of each problem with labels of states of a substance; Assign STATE 1 at the inlet of a high-pressure turbine. The states must be arranged in a chronological order; Plot each cycle in a t-s diagram with thestates consistent to the states assignment in the schematic diagram; A reheat-regenerative Rankine cycle receives steam at 8.0 MPa, 300 0C and exhaust at 0.01 MPa. Steam is extracted at 2.0 MPa for CFWH and the remainder for reheating. The reheated steam enters the 2nd stage turbine at 1.5MPa and expands to 1.0 MPa where more steam is extracted for OFWH. The remainder expands to the condenser pressure of 0.01MPa. Feedwater from low pressure regenerative heater leaves the CFWH at 207 0C and mixes with the feedwater. Determine the percentages of the extracted steam and the cycle thermal efficiency.
For dry saturated steam the value of specific entropy is equals to a. zero b. sg c. sf d. sfg
In a cycle, a 4kg ideal gas(MW=3g/mol and k=2.3) confined in a controlled mass system went through three processes.the gas was started at 20kPa and 310K in the first process, and it was isometrically increased by 30kPa. The gas subject to 400Kusing a process defined by PV^3=C.It returns to its original state polytropically.Calculate the entropy change for each process.
PROBLEM:A turbine is designed to operate with nitrogen N2 as working fluid. At steady state thenitrogen pressure and temperature at the turbine inlet are 13 bar and 300℃, respectively.The nitrogen pressure at the turbine outlet is 2 bar. The isentropic turbine efficiency is of80%. Question:(a) Calculate the work developed by the turbine per unit of mass flowing.(b) Calculate the nitrogen temperature at the turbine outlet.
Steam power plant shown in figure isoperating at steady state with water as the workingfluid. The mass flow rate of the water circulatingthrough the components is 50 kg/s. Determine: d) isentropic pump efficiencye) mass flow rate of the cooling water, in kg/s.f) rates of entropy production, each in kW/K, forthe turbine and steam generator.Include all the relevant governing equations andreferences to the tables you use. Be organize
Need Help going through the process on how to solve this problem. May accidentally be asking this a second time, because the first time I asked it, it didn't show as a pending problem. Steam expands adiabatically through a turbine at steady state. The entering stream is at 750 lbf/in^2, 750°F, and the exiting stream is a saturated vapor at 10 lbf/in^2. Kinetic and potential energy effects are negligible. a. How much work per lb of flow does the turbine produce, in Btu/lbm? b. If the turbine produces 3000 kW of output power, determine the mass flow rate of steam in kg/s. c. If this process were isentropic, the existing stream would no longer be a saturated vapor. Determine the final quality of steam in that case. d. Determine the isentropic turbine efficiency.
Steam undergoes an adiabatic expansion in a piston-cylinder assembly from 30 bar, 360°C to 3 bar, 240° C. What is work in kJ per kg of steam for the process? Calculate the amount of entropy produced, in kJ/K per kg of steam. What is the maximum theoretical work that could be obtained from the given initial state to the same final pressure?