Describe the Composite Areas?

Q: List the main pros and cons of utilizing composite materials in the aircraft structure.

A: Composite materials are widely used in aircraft structure due to their unique properties of…

Q: mass of the copper?

A: GIVEN- Heat (q) = 1386J T1= 20 deg.c T2= 80 deg.c Copper heat capacity (C) = 0.385 J/g ° C   To…

Q: How does the LRFD method of design react on the load and strength of the material?

A: LFRD means Load and resistance design factor is a method of design of steel structures and…

Q: What do most of the engineering materials exhibit?

A: On a macro scale, materials can simply be classified as one of two basic types: Isotropic…

Q: Non-destructive testing of large molded pieces may be performed using radiation. Discuss what…

A: Given question: Discuss what constructive elements a non-destructive testing system should contain,…

Q: Name three alloying agents and their principal effects.

A: given: Name three alloying agents and their principal effects

Q: Describe the various types of supports of columns?

A: A column is defined as a structural member subjected to axial compressive loads during its…

Q: Q\Why the metals family could be strengthening

A: Both crystalline and amorphous materials may have their yield strength, ductility, and toughness…

Q: What is the reactive force?

A: Reactive force is generated inside a body when an external force is applied over it. Without the…

Q: Define the term, curved members?

A: Curvature strongly affects the way a structure carries external loads. A common example of a curved…

Q: hat are the parts made by cast iron ?

A: Mainly three parts are made by Cast Iron 1. Body 2. Spindle bearing 3. Hand Wheel

Q: There are several ways of shaping plate or sheet glass. Name and briefly describe one of them.

A: The methods described in this text are : Rolling-In tis process  the hot glass is squeezed between…

Q: A 2m? glass panel needs to be processing would you recor toughening is achieved.

A: Toughened glass has undergone processes of controlled thermal treatment (the process of heating and…

Q: Describe the defects found on the injection/ compression moulded parts with different temperatures…

A: There are several defects those are found on injection/compression moulded parts..... Those are as…

Q: Which material should be chosen when high strength is required

A: Given: To define: Which material should be chosen when high strength is required

Q: The needle form of mullite offering substantial increasing in structural strength and heat…

A: Mullite :- Mullite or Porcelainite is a rare silicate mineral of post clay genesis. It can form two…

Q: Describe the Poisson's Ratio?

A: Poisson's Ratio: It is the ratio of lateral strain to longitudinal strain. The value ranges from…

Q: When is the plastic analysis used?

A: In plastic analysis it is assumed that material is in plastic state where deformation increases…

Q: What cross-sectional property is influenced by the size effect factor between the depth and width of…

A: The properties that get affected by the depth and the width of the member are given below: (A) The…

Q: What does the slenderness ratio serve as?

A: The slenderness ratio is defined as the ratio of effective length to the least radius of gyration.…

Q: what would be the most appropriate choice for the bulk material used for a turbine blade in a jet…

A:

Q: Proposed Destructive and Non-destructive techniques for following, Final Rubber product…

A: Destructive testing Nondestructive testing External cracks Fatigue test Liquid Penetrant test…

Q: Why should special attention be given to the design of columns?

A: Columns are the vertical members in a structure. They resist compression loads. Columns are the…

Q: What are the factors that that affect the casing design internally and externally?

A: Casing is an essential part of drilling and completion of an oil and gas well. Casing allows us to…

Q: When are the thin-walled tubes of the noncircular cross-section often used to construct?

A: Thin-walled tubes are the thickness of the tube is less than 1/20th  of the diameter of the tube.…

Q: Q16. A mug is to be made from alumina. Which forming method would be most suitable?

A:

Q: Explain with neat sketch, “Anodizing” heat treatment process.

A: To find : , “Anodizing” heat treatment process with neat sketch

Q: What are the long slender columns?

A: Solution:

Q: Are the composite areas divided into several parts having simpler shapes?

A: The properties of composite areas are generally solved or analyzed by dividing them into simpler…

Q: What is  central impact?

A: When the directions of motion of the two colliding objects are along the line of impact, the central…

Q: What are the Intermediate columns?

A: columns can be classified into 3 type - long , short and intermediate

Q: What is the plastic load?

A: The load at which the structure is the collapse is known as the plastic load.

Q: Define the term falling block?

A: it is an action which is used in rifle. it is single shot firarm action

Q: Q1:T shaped Mild Steel beams are widely used in structural fabrication activities, examine the shown…

A:

Q: each material in the composite may provide to the overall part. What problems might the different…

A: Given: Manufacturing of piston for automobile TO write: Benefits of using silicon carbide material…

Q: Which of the following characteristics is not describing additive RP methods? Staircase appearance…

A:

Q: Briefly describe the process and then identify at least one type of product which can be…

A: given; Briefly describe the process and then identify at least one type of product which can be…

Q: Basic Steps for Mold Making ?

A: Basic Steps for Mold Making

Q: Expalin the Beams on Elastic Foundations ?

A: A beam resting on the elastic support is said to be a beam on the elastic foundation. When a beam is…

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.