Question

What is the reactive force?

Expert Answer

Want to see the step-by-step answer?

Check out a sample Q&A here.

Want to see this answer and more?

Experts are waiting 24/7 to provide step-by-step solutions in as fast as 30 minutes!*

*Response times may vary by subject and question complexity. Median response time is 34 minutes for paid subscribers and may be longer for promotional offers.
Tagged in
Engineering
Mechanical Engineering

Classical Mechanics

Related Mechanical Engineering Q&A

Find answers to questions asked by students like you.

Q: 17-105. If the coefficient of static friction between the 50-lb roller and the ground is u, = 0.25, ...

A: Click to see the answer

Q: 17-98. The spool has a mass of 100 kg and a radius of gyration kg = 0.3 m. If the coefficients of st...

A: Given that: The mass of the spool is m =100 kg. The radius of gyration is KG =0.3 m. The coefficien...

Q: Does a cycle for which ∮ δQ > 0 violate the Clausius inequality? Why?

A: Yes, the ∮ δQ > 0 violate the Clausius law of inequality because the Clausius law of Inequality i...

Q: Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges...

A: Given data Determine the flow rate of oil through the pipe if the pipe is (a) horizontal (b) incli...

Q: Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts fittin...

A: Given, Pb = 200 MPa. Ps=130 MPa db=16 mm The diagram shows that the nut and bolts are applying a ten...

Q: Portions of a 1/2 x 1/2 -in. square bar have been bent to form the two machine components shown. Kno...

A: Given Data: The coss-sectional area of the squer bar is: 0.5 X 0.5 in2. The allowable stress is : σ...

Q: The temperature difference between the hot and cold fluids in a heat exchanger is given to be ∆? at ...

A: The symbols representing the temperature difference in the hot and cold fluids at each end are not w...

Q: Describe the normal pedal feel when the ABS is activated during hard braking?

A: Anti braking system(ABS):  Anti braking system(ABS) allows a driver to apply the brakes  quickly whe...

Q: For specified inlet and outlet temperatures, for what kind of heat exchanger will the ∆? be the grea...

A: For specified inlet and outlet temperatures, for what kind of heat exchanger will the ∆? be the grea...

Q: The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 8...

A: Given, L=2m Do=40mm=0.04 m ro=20mm = 0.02 m Shear Stress= 140 MPa ω= 80 rad/s

Q: During a manufacturing process, a conveyor belt starts from rest and travels a total of 1.2 ft befor...

A: The data given is,

Q: The A-36 steel bolt is tightened within a hole so that the reactive torque on the shank AB can be ex...

A: On applying torque equilibrium at the bolt,  

Q: Disk A has a mass mA = 4 kg, a radius rA = 300 mm, and an initial angular velocity ω0 = 300 rpm cloc...

A: Disk A Mass = 4 kg Radius = 300 mm Angular velocity = 300 rpm clockwise Disk B Mass = 1.6 kg Radius ...

Q: A fan is to accelerate quiescent air to a velocity of 8 m/s at a rate of 9 m3 /s. Determine the mini...

A: Given: The velocity of the quiescent air is v=8 m/s The volume rate of the quiescent air is V=9 m3/s...

Q: The two forces act on a bolt at A. Determine theirresultant.(graphical solution)

A: Applying the graphical method First of all, a parallelogram with sides equal to P and Q is drawn. Th...

Q: Answer all the points, please

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If y...

Q: The double pulley shown has a mass of 15 kg and a centroidal radius of gyration of 160 mm. Cylinder ...

A: Let rA be the radius of the outer pulley and rB that of the inner pulley. Write the expression of th...

Q: A gas initially at a subsonic velocity enters an adiabatic diverging duct. Discuss how this affects ...

A: (a) When a gas is flowing at the subsonic velocity and passed through a diverging duct, its velocity...

Q: The L-shaped frame is made from two segments, each of length L and flexural stiffness EI. If it is s...

A: The moment due to distributed load about the point B is The vertical displacement of the point B is...

Q: A 7-hp (shaft) pump is used to raise water to an elevation of 15 m. If the mechanical efficiency of ...

A: The mechanical efficiency of the pump is η=0.82 The height of the water to be pumped is H=15 m The i...

Q: 10-45. The rotating flywheel-and-shaft, when brought to a sudden stop at D, begins to ascillate cloc...

A: Given data: Arc length, s = 6mm Radius of the wheel, R = 75mm Shaft inner dia, d = 24 mm Shaft outer...

Q: The dry bulb and wet bulb temperatures of a room are measured as 30C and 20C, respectively. After mo...

A: The two points are shown on the psychometric chart below. Initial point -1 Final point -2

Q: Select the lightest-weight wide-flange beam with the shortest depth from Appendix B that will safely...

A: Given data: Allowable bending stress, σallow = 24 ksi Allowable shear stress, τallow = 14 ksi   Draw...

Q: the magnitude of gravitational force is?

A: Gravitational force: The magnitude of the gravitational force is the multiplication of the masses of...

Q: *19-16. The frame of a tandem drum roller has a weight of 4000 lb excluding the two rollers. Each ro...

A: Given Frame weight = 4000 lb Roller weight = 1500 lb Radius of gyration = 1.25 ft Rear torque = 300 ...

Q: Question 2.2 Two 3 m long and 0.4 cm thick cast iron (k= 52 W/m-K) steam pipes, of outer diameter 10...

A: Given data

Q: Using a handheld bicycle pump to generate an airjet, a soda can as the water reservoir, and straw as...

A: Consider the diagram shown below for the atomizer build from bicycle pump, straw and soda can.

Q: A rectangular channel with a bottom width of 7 m discharges water at a rate of 45 m3/s. Determine th...

A: The data given is, Discharge, Q = 45 m3/s Rectangular channel width, b = 7 m

Q: Determine the second moment of area for the shaded region shown in Fig. with respect to The y-axis. ...

A:  

Q: You are working as an expert witness for the owner of a skyscraper complex in a downtown area. The o...

A: Part (a) Plan (ii) is a much more dangerous situation in terms of windows popping out than Plan (i) ...

Q: The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V t...

A: Given data: *The allowable shear stress σall=7 MPa. *The total length of the section is B=200 mm. *T...

Q: A 1:30 model of a ship is made. The real ship has a hull length of 130 m and travels at 7.9 m/s. Fin...

A: Click to see the answer

Q: A 20 in. long work piece with a cross sectional area of 2 in? (see the accompanying figure) is stret...

A: Click to see the answer

Q: Use the rectangular component method to solve the fol- lowing problems. Determine the magnitude R of...

A: Write the expression of the forces acting in the x-direction. Write the expression of the forces ac...

Q: A rigid tank contains 7.5 kg of saturated water mixture at 400 kPa. A valve at the bottom of the tan...

A: Given data: *The amount of saturated water mixture at 400 kPa is m1=7.5 kg. *The pressure in the tan...

Q: Water flowing through a sluice gate undergoes a hydraulic jump, as shown. The velocity of the water ...

A: Let us consider that the width of the channel is sufficient in order to neglect the end effects. The...

Q: It is an embedded support at point A of the beam, whose loading status is given below. Find only the...

A: Click to see the answer

Q: The static and stagnation pressures of a fluid in a pipe are measured by a piezometer and a pitot tu...

A: Given Data: The stagnation pressure of the fluid is: H0= 2.2 m. The static pressure head of the flu...

Q: *18-52. The two 12-kg slender rods are pin connected and released from rest at the position 6 = 60°....

A: Write the given data: Understand the following diagram for the initial and final position of the sy...

Q: 3-11 Detormine the forces in cables A and B if block Wof Fig. P3-11 weighs 350 Ib.

A:  

Q: A rigid plate, having a weight of 100 lbs acting at its center, is connected to a 'ball and socket' ...

A: Click to see the answer

Q: Consider a thermal energy reservoir at 1500 K that can supply heat at a rate of 150,000 kJ/h. Determ...

A: Given: The temperature of the thermal reservoir is T1=1500 K. The temperature of the environment is ...

Q: The water needs of a small farm are to be met by pumping water from a well that can supply water con...

A: The data given is, Discharge, Q = 4 L/s Pipe dia, D = 5 cm = 0.05 m Dyanmic viscosity, ? = 0.00131 ...

Q: 22-33. If the 20-kg wheel is displaced a small amount and released, determine the natural period of ...

A: Given: The mass of the wheel, m = 20 kg The radius of the gyration, KG = 0.36 m The spring stiffness...

Q: F15–10. The spring is fixed to block A and block B is pressed against the spring. If the spring is c...

A: Given Data: The mass of block A is MA = 10 kg. The mass of block is MB = 15 kg. The spring constant...