Describe the process of Feedforward Regulation system?

Q: Explain with the help of diagram the working principle of low temperature and adsorption dryers.

A: The general working principle of adsorption dryers is simple: moist air flows over hygroscopic…

Q: What are the types of Axial Fan?

A: In Axial fan the air flows parallelly to the motor driven shaft of the axial/propeller fan. They can…

Q: How long would it take to purge a 15ft section of 6in diameter pipe using a flow rate of 35cfh?

A: Given data length of the pipe L = 15ft  diameter of the pipe = 6in = 0.5ft Flow rate = 35cfh  To…

Q: Which one of the following reboiler requires more complex pipe work? Horizontal thermosyphon…

A: Horizontal thermosyphon reboiler are depends on natural circulation where in shell sides,…

Q: Describe four ways in which the heater control valve may be controlled

A: The heater control valve is a part of the heating ventilation, and air conditioning unit (HVAC) used…

Q: what should you know before choosing a respirator

A: Workers should use respirators for cover from contaminants within the air on condition that…

Q: Why is the remaining fluid at the delivery tip of a Mohr pipet is not blown out?

A: A Mohr pipette is a type of pipette that is used to measure the volume of any liquid solution…

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: DESCRIBE THE PROCESSES AND CYCLES?

A: Consider the PV diagram shown below for a process and cycle.

Q: Complete the diagram below by positioning labels into the correct position, identifying the main…

A: Solution:   The complete labelled diagram is given below:

Q: Draw the Ts diagram of the whole process

A:

Q: For what application are the pressure control valves seen in Figure 2 being used?

A: Introduction The valves enable the regulation of system pressure to adjust the force on a hydraulic…

Q: 14. What type of reactor does this appear to be? 0.368+

A: this type of graph shown second order reaction.

Q: One way to prevent leaking from glove valves in a Halocarbon refrigeration system is to employ…

A:

Q: What is open countercurrent spray tower?

A: A spray tower (or spray column or spray chamber) is gas-liquid contactor wont to win mass and warmth…

Q: Why should the adiabatic flame temperature be much higher for a pure oxygen feed than for an air…

A: -The temperature of the products of the combustion reaction if no heat is lost in the external…

Q: Explain the the fan design procedure?

A: Given Fan Design To find Design procedure of fan

Q: shadow price

A: Given;  Determine  the shadow price of the source? Where,  In a linear programming problem, if a…

Q: heat rate

A: From steam table At 5MPa and 450oCh3=3317.2 kJ/kgs3=6.8210 kJ/kgK Process 3-4 is isentropic…

Q: How long would it take to purge a 15 foot section of 6 inch diameter pipe using a flow rate of 35…

A: Given that -  Flow rate = 35 cubic feet per hour Length (L) = 15 feet Diameter (d) = 6 inches = 0.5…

Q: List some applications that use low-pressure piping

A: The low-pressure piping systems are used to carry nonhazardous materials that are used in Industry.…

Q: What areas within a vane pump or motor are the most susceptible to contamination-induced clearance…

A: Vane Pump :  A vane pump is a type of positive displacement pump that delivers a constant flow rate…

Q: 4. What is the purpose of a sequence valve and how is this typically accomplished?

A: To find:-    Purpose of sequence wall and how is this accomplished

Q: Choose the correct answer The discharge pressure of a refrigerant should be as constant as possible…

A:

Q: 7.2 Explain the principle of a pilot-operated valve. 7.3 Explain how a sequential valve can be used…

A:

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: How does a thermal expansion valve work?

A: A thermal expansion valve or thermostatic expansion valve (often abbreviated as TEV, TXV, or TX…

Q: Actions to be taken including HSE considerations while freeing the stuck pipe which include the…

A: The drilling jars are the tools that are present on the drill string. The jar enables to knock the…

Q: Discuss three ways to remove water from the air in an air distribution system.

A: Moisture is ever present in the atmosphere. It can affect air distribution systems by affecting…

Q: Describe the range of maintenanceactivities.

A: It is a task that is to be performed to preserve an asset. The task help to provide continuity and…

Q: A) What are the requirements for a good boiler

A: Requirements for a good boiler:

Q: he world valve on the cutting attachment is called the

A: we have to figure out what kind of valve is used in oxyacetylene welding regulator

Q: Heavy internal springs are used to establish the operating pressure of the -operated type of…

A: In  hydraulic system pressure is controlled by metering the flow of fluid into or out of…

Q: According to the API code, pipes of the same nominal diameter should be fitted so the offset is no…

A: The welding of pipes should be done by the qualified workers. The offset for same nominal diameters…

Q: Describe the following point-of-operation devices: (a) automatic or semiautomatic feed and ejection…

A:

Q: Describe a direct-expansion versus a flooded evaporator.

A: Flooded Type Evaporator: Compared to a dry type, a flooded type evaporator transfers heat more…

Q: Screening, filteration, settling,centrifuging are t various methods used for solid liquid seperation

A: Screening : Screening is th e passing of material through distinct and uniform openings is the main…

Q: What is a standpipe?

A:

Q: chat ope DE aintains tracted

A: Obtain the properties of steam at state 6 from table A - 6 "properties of super- heated water" at a…

Q: Discuss boiler feed water properties, treatment and sampling procedure.

A:

Q: Table 7.1- values of coefficient of pipe friction (research the table please)

A:

Q: f the desc oth of cut rations

A: Chip forming ;

Q: What recommendation would you suggest for improving the performance of the ground-source heat pump

A: The performance of ground source heat pump can be improved by

Q: Describe the types of Pressure and how to mesure.

A: Pressure  - Pressure is defined as the force applied perpendicular to an object per unit area.…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.