he world valve on the cutting attachment is called the

Q: True or False: The JOIN command requires that line segments must lie end to end with no gaps or…

A: The JOIN command joins similar objects to form a single unbroken object. The JOIN command combines a…

Q: is used to cut machine other material. O Chromium steel Nickel steel O Martensitic tool steel O Tool…

A: To find the material that are used to cut machine other material .

Q: State the OSHA safety procedures of performing oxy/acetylene cutting and other gas cutting process

A:

Q: Describe the process of Feedforward Regulation system?

A: In feedforward regulation system controller identifies the errors within the system before output…

Q: Explain what happens at each stage of the machine's cycle

A: A machine cycle is consist of four steps. These steps are fetch, decode, execute and store. The…

Q: clearance in the assembly

A: Given; In an interchangeable assembly, shafts of size = 25.00-0.0100-0.040mmsizes of  holes=…

Q: Water is flowing thru the pipe set-up. What can be the v thru pipe 3 ?

A:

Q: The tool used for cutting the sheet metal after marking is called snips. Select one: O True False

A: given that the tool used for cutting the sheet metal after making is called snips  true  false  in…

Q: For what application are the pressure control valves seen in Figure 2 being used?

A: Introduction The valves enable the regulation of system pressure to adjust the force on a hydraulic…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Check valves are often used with other valves to?

A: Check valves are often used with other valves to

Q: The following tool is used to cutting internal threads of drilled hole Select one: a. Drill plate b.…

A: It is required to which tool is used to cutting internal thread of drilled hole

Q: how does a pilot check valve differ from a simple check valve

A: The check valves are used for the seal age purpose in the closed position. The valves are used for…

Q: velocity of the rod

A: Given: A point mass of 0.001 kg hits its normally at 200 cm/s at the locationas shown.The plane in…

Q: ic, calculate the heat loss from the rod.

A: To find the heat loss from the rod.

Q: "hich one of the following

A: given:

Q: to : 4) Horizontal component of pinch force tries Cause the arc blow Reduce the cross-section of the…

A: Pinch force :- The flow of current through the arc gap can produce or developed the electromagnetic…

Q: 5. Name a tool that can be used to check an internal thread.

A: In this problem, it is asking about the name of the tool that can be used to check an internal…

Q: 4. What is the purpose of a sequence valve and how is this typically accomplished?

A: To find:-    Purpose of sequence wall and how is this accomplished

Q: The technician............... machine, but ............... no time. He wasn't very busy. to repair…

A: GIven

Q: Explain where did 23.4 came from

A: Use linear interpolation technique to calculate saturation pressure at 20 degree Celsius.

Q: Enumerate the steps in cutting and piercing a plate using gas cutting

A: The oxyfuel process is the most extensively used industrial thermal cutting technique because it…

Q: Describe the action of a commutator.

A: Introduction to commutator: commutator is a mechanical part of DC generator or motor which converts…

Q: What is a check valve? What does it accomplish?

A: Concept: 1) Check valve is a uni-directional valve.  2) It's also called as non_return valve.  3) It…

Q: types of cutting processes that are cleanly cut for preparing edge

A:

Q: Describe different simple machines.

A: A simple machine is defined as the mechanical device which is capable to change the direction or…

Q: the bolt is

A:

Q: Drilling operation to produce conical shape on a drilled hole is known as a. Boring b. Counter…

A:

Q: Steps of how to draw a valve of an IV cannula using

A: Dassault Systèmes' SolidWorks is a solid modelling computer-aided design and computer-aided…

Q: While Drilling it is permissible to leave the check key in check while drilling a hole.

A: While Drilling it is permissible to leave the check key in check while drilling a hole. Answer:…

Q: List down any four safety precaution need to carry during the operation of Lathe machine.

A: Some safety precautions that need to be followed during the operation of Lathe machines are as…

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate…

Q: The operation where enlarging a hole is called (A) Reaming (B) Drilling (C) Tapering (D) Boring.

A: Machining: Machining is a manufacturing process that involves cutting material into perfect shape…

Q: What is 5 and 2 in 5/2 two way valve

A: Valve: A valve is a device that regulates the flow of fluid by opening and closing or partially…

Q: is reduced icinal is

A:

Q: List out the operation need to carry for completing the job in radial arm drilling machine?

A: operation need to carry for completing the job in radial arm drilling machine...

Q: 24. Avoid using compressed air to clean chips from the nmilling machine because.. a. it does the job…

A: It can create a dangerous environmental situation, flying chips may cause eye injuries, and it…

Q: List three things that can become a problem when cutting and affect your ability to make a quality…

A: It important to make good-quality cuts as bad cuts cause hard slag and there is more extra work…

Q: Which part of the drilling machine holds the job while performing drilling operations? Select one:…

A:

Q: Guve the safety procedure on this process

A: The shaper machine is a reciprocating machine that is mostly used to create horizontal, vertical, or…

Q: 12. The following is concerned with the depth of the hole: * Drilling operation Drilling operation…

A: Blind-hole is defined as the a hole that is drilled or reamed to a certain depth without going…

Q: figures sho ed to a con Mat the free

A:

Q: The third (green) wire on an electric drill is the _________ wire.

A: Given Data : Third(Green) Wire

Q: The wrenches are used for clearing burrs from work surfaces. Select one: True False

A: The wrenches are used for clearing burrs from work surfaces. Select one: True False

Q: Describe the types of Pressure and how to mesure.

A: Pressure  - Pressure is defined as the force applied perpendicular to an object per unit area.…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.