f the desc oth of cut rations

Q: travelling ke to stop with W1 WI ning

A:

Q: PA

A: given:

Q: the block A vertical

A:

Q: vill become tu

A:

Q: how much wilu he need to invert

A: Given: A=3220000 R=1.85% n=2 t=5 To determine: Principal amount

Q: ane area is

A:

Q: S teath oulat

A:

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: pot

A:

Q: Q Heat t reatments and theireFfects2

A: Concept: Heat Treatment Methods are In this methods, the steels materials are heated to upper…

Q: IS ading edg

A:

Q: يمكننا إدخال رقم صفحة من خالل 0 0 ( Footer Both Header and Footer > Header None of the above > O

A: In the Microsoft we can enter page number in the footer. Header

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: , and an inlet F e Air exits with a termine the Foll

A: given:T1=660CV1=40FT/SP1=140PSIP2=15PSI

Q: eaga (w)=1 rade\s counter cloch

A:

Q: from the fu

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Two inward flow to

A: 437 RPM

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: esistanc

A:

Q: fires

A: A spark is created when the applied electric field exceeds the dielectric breakdown strength of the…

Q: outlet mean temperature of the water.

A: Given: Heat generated=5 kW m=0.2 kg/s Cp=4.18 kJ/kgK Ti=25oC To determine: Outside temperature

Q: Iflow rat

A:

Q: if Op1 is 18.6 °ccw, then Os1 is . CW

A:

Q: ne cost to operate the bulb

A: Given- P= 60W t= 30 days ( power on at 18hr/day) cost= 10cent/kWh Need To calculate the Operating…

Q: Qin > Qout in (mark all that apply):

A:

Q: Answqer b) only

A:

Q: e is pl= Eransfe

A: Diameter of the rod (tube) d = 50 mm Ts = 383 K   T∞ = 373 K Properties of water at 100∘C ( 373 K)…

Q: ond ch unit of the fi e is a quarter of o manufacture

A: The given LPP will  be solved from graphical method. Subject to constraints:400x1+700x2≤10000x1+0x2…

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: D raio s.f.D and B.M.

A:

Q: how to get the -y theo

A:

Q: ged at D and E.

A:

Q: ut of tha

A:

Q: al is the magni

A:

Q: ng air has the follo neat added to the air °R and K = 1.4. Con

A:

Q: etermine the minimum clearance in the assembly.

A: To determine the minimum clearance in the assembly.

Q: ure at 21

A: given:

Q: he world valve on the cutting attachment is called the

A: we have to figure out what kind of valve is used in oxyacetylene welding regulator

Q: t it is tha

A: Given data SEM Image of fracture surface is given  Required  Identification of types of fracture…

Q: O a. an expanding hot gas O b. hand

A:

Q: is reduced icinal is

A:

Q: Need three views

A: According to the details provided in the question, we need to find three views.

Q: ss is 8 1.

A: given mass m=80kg

Q: rope is wrapE

A:

Q: e relative efficienc

A: relative efficiency = 6.35%

Q: • What is: d cos(at +d), dt

A:

Q: D, the smallest pipe for

A: GIVEN- Re= 2300 Q= 1L/s TO FIND- Smallest pipe (D)

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.