Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the mainpower supply of (220 Vrms). Find: -1- The transformer turns ratio (a).2- The ripple voltage.Voludit)Vm = 12 V3- The Vde value.4- The RMS value of the output voltage.5- The ripple factor.6- The value of capacitor filter.= 0.1 V(assume ideal diodes)T=0.01 sec.tisec)

Answered: Image /qna-images/answer/b5df7ce8-8f6a-4764-a3de-16cb9aae23ff.jpg

Design a Bridge FWR to supply a load of (100) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vo Vm - 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip =0.1 V (assume ideal diodes) T=0.01 sec.

Design a Bridge FWR to supply a load of (100) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). 2- The ripple voltage. Vo Vm - 12 V 3- The Vde value. 4- The RMS value of the output voltage. 5- The ripple factor. 6- The value of capacitor filter. Vip =0.1 V (assume ideal diodes) T=0.01 sec.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain the PWM control and duty cycle generation in phase-control of SCR
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
For a switching regulator with a square wave output, the DC levels is given by the formula . Where Vdc is the output, Vmax is 12V, Vdrop is the saturation drop (on) of our switching device which is 0.7V, T is the period and Ton is the time Vmax is on for a period. Find the duty cycle in % needed for Vdc 10V and 5V. Find the efficiency for 10V and 5V output operation using Powerout/(powerout+powerloss)
During turn-on and turn-off of a power transistor, thecurrent-time and voltage-time relationships are asshown in the adjacent figure. Observe the waveformsand calculate,40) the OFF-state power dissipation (static);41) the switch ON-state power dissipation(static);42) the average switching loss for the OFFtransition (dynamic);43) the average switching loss for the ONtransition (dynamic);Assume a switching frequency of 2kHz with 397V as specified in Appendix A.
Draw the block diagram of a HVDC converter station and briefly describe the function of each Component.Define LCC and VSC and compare their performance
For a single-phase Ac-Ac Converter with unidirictional phase control, find the output dc voltage, where, the delay angle is 0 degree, the input voltage is 120sinwt with 10ohm resistive load consider
A particular load has to be supplied with an average power of 50mW, 5V dc voltage. Find the value of capacitance and transformer turns ratio in a half wave rectifier with capacitor filter such that the ripple factor should not exceed 1%. Assume 220V rms, 50Hz supply voltage. Also, sketch the voltage waveform across the load.
A three-phase to three-phase, three-pulse cycloconverter operating in circulating current-free such that the input / output frequency ratio is fi / fo = 9. What are typical frequencies of the low-order higher harmonics ?
Design a CT-FWR to supply a load of (50) with a waveform of the following specifications: -  Vdc = 12 V  Ripple factor = 0.1 %  the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Methodology of report Title:dc to dc converter with PID controller
Describe different control schemes of AC regulators and derive the expressions of average andeffective values of output voltages. i need a short answer and correct answer plerase