Question 2.aAn ac power supply with VRMS =240 V and a full-wave rectifier are used to generate a devoltage for a resistive load with resistance value of 100 Q. The filter capacitor connectedto the rectifier has capacitance value of 500 µF. The frequency of the ac supply is 50-Hz.Determine the de voltage and ripple factor at load side?а.Question 2.bAssume that by using an RC filter circuit, you wanted to reduce the ripple factor to half theamount that you calculated in part 2.a, answer the following questions:b.What values would you suggest for resistor and capacitor of the RC circuit?What is the voltage regulation of this circuit?с.

Note: I am doing the first part due to complexity of the problem, I can solve first part in the…

Question 2.a An ac power supply with VrMs =240 V and a full-wave rectifier are used to generate a de voltage for a resistive load with resistance value of 100 Q. The filter capacitor connected to the rectifier has capacitance value of 500 µF. The frequency of the ac supply is 50-Hz. a. Determine the de voltage and ripple factor at load side? Question 2.b Assume that by using an RC filter circuit, you wanted to reduce the ripple factor to half the amount that you calculated in part 2.a, answer the following questions: b. What values would you suggest for resistor and capacitor of the RC circuit? с. What is the voltage regulation of this circuit?

Question 2.a An ac power supply with VrMs =240 V and a full-wave rectifier are used to generate a de voltage for a resistive load with resistance value of 100 Q. The filter capacitor connected to the rectifier has capacitance value of 500 µF. The frequency of the ac supply is 50-Hz. a. Determine the de voltage and ripple factor at load side? Question 2.b Assume that by using an RC filter circuit, you wanted to reduce the ripple factor to half the amount that you calculated in part 2.a, answer the following questions: b. What values would you suggest for resistor and capacitor of the RC circuit? с. What is the voltage regulation of this circuit?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A step-down transformer supplies 25Vrms to a simple half wave rectifier power supply which is connected to a load resistance of 912ohm. The diode breakdown voltage, Vf is 0.7 V. Calculate the amplitude of the peak output voltage, Vpo appearing across the load., calculate the average DC voltage appearing across the load, calculate the DC current in mA drawn by the load.
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
2.A single phase uncontrolled half wave rectifier has a transformer with a turns ratio of 5:1, has a source of 220Vrms at 60 Hz frequency, its supplies the load with a 100ohm resistance. Find: A. Average voltage and current and also in RMS B. Power and ripple factor
Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
Draw the circuit diagram of a single phase full-wave uncontrolledrectifier with R-load. Describe its principle of operation. Draw thewaveforms of: input voltage, voltage across the load, current throughthe diodes and their voltage. Write the expressions for: the averageoutput voltage Vd, the maximum reverse voltage across the diode and thestandard transformer power. Describe what the difference will be if acapacitor is added in parallel with the load at the output.
) Determine the reading obtained withaDC voltmeter at RB when the switch is set at point B. b) Determine the reading at thesame RBusing ½ wave and Full wave rectifier AC meter respectively when the switch is set at point A. Given that Ifs = 100-µA and set at 10-V dc or rms range.
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 6.2 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the value…
Design a center-tapped full-wave Rectifier Circuit to provide an output of 100 VDC. Then calculate its transformer peak voltage rating, the diode PIV rating, and the transformer turns ratio, if the power is taken from the 220V line AC supply
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?