Design a one-input, one-output sequence detector, which produces an output 1 every time the sequence 1111 is detected, and an output 0 at all other times. The circuit is also required to recognize overlapping sequences, as can be seen in the output string z that results from the following input string x. Use JK flip-flops. Use the following input string as part of your simulation. Input string x: 1101111111010 Output string z: 0000001111000

Design a one-input, one-output sequence detector, which produces an output 1 every time the sequence 1111 is detected, and an output 0 at all other times. The circuit is also required to recognize overlapping sequences, as can be seen in the output string z that results from the following input string x. Use JK flip-flops. Use the following input string as part of your simulation. Input string x: 1101111111010 Output string z: 0000001111000

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

a) Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allows the digital information from multi-inputs to a single output line(b) Design a 8 to 1 multiplexer by using the four variable function given by F (A, B, C, D) = ∑m = (013489 15) (c) OUR school AIT has lockers in all the campus that she often rent them out to students who needs them, upon graduation they are taken back by the school authorities. Kindly express the process of opening this locker in terms of digital operation.
We wish to design a digital system with two flip-flops, say B and C, and one 4-bit binarycounter A, in which the individual flip-flops are denoted by A4, A3, A2, A1. A start signal Sinitiates the system operation by clearing the counter A and flip-flop C, and settling flip-flop B toone. The counter is then incremented by one starting from the next clock pulse and continues toincrement until the operations stop. Counter bits A3 and A4 determine the sequence ofoperations:If A3 = 0, B is cleared to 0 and the count continues.If A3 = 1, B is set to 1; then if A4 = 0, the count continues, but if A4= 1, C is set to 1 on the nextclock pulse and the system stops counting.Then if S = 0, the system remains in the initial state, but if S = 1, the operation cycle repeats.(a) Draw the ASM Chart(b) Draw the equivalent one flip-flop per state
Using T flip flops, design a 3 bit counter which counts in the sequence: 111, 110, 101, 100, 011, 010, 001, 000, (repeat)111... (a) complete the following truth table with next stages and flip flop inputs CBA C+B+A+ TcTbTa 000 001 010 011 100 101 110 111 (b) Draw the Karnaugh maps for Tc, Tb, Ta (c) Using the Kamaugh maps, find the minimum sum of product for Tc, Tb, Ta
Draw the circuit, and show the truth table, for the clocked Master-Slave JK ﬂip-ﬂop
The state diagram of a sequence which allows overlap is shown below. A sequence detector accepts input a string of bits:either 0 or 1. Its output goes to 1 when a target sequence has been detected. In a sequence detector that allows overlap, the final bits of one sequence can be the start of another sequence. Using the state diagram given below and an input sequence 10110: A) Assign binary values to the states and derice the state table. B)derive the simplified state equations. c) Use JK flip-flop abd design a synchronous sequence detector circut. D) Is this Mealy or Moore model? Treat unused states as do not care conditions
Design of a digital electronic circuit that produces 4 bits of binary numbers sequentially and repeatedly to move the Stepper Motor in Full Step mode such as : 0011 1001 1100 0110 0011. To generate predefined binary data, You can use a flip-flop that is assembled into a Sync Counter. To stringing a flip-flop into a Sync Counter must be known Excitation Table or Table Transition from flip-flop. Citation Table determined by Table The Truth of the Flip-Flop. Design of Synchronous Counter circuit to generate 4 bits of Motor drive data Stepper on Full Step mode using a D flip-flop?
Kindly design a Master-slave J-K flip-flop using NAND gates only and staterace-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allowsthe digital information from multi-inputs to a single output line
Create a 5-bit shift right register using D flip-flops. Given an initial value of Din=1 and Q4 Q3 Q2 Q1 Q0 = 10101, what will be the final value after the 4th clock pulse if Din=0 upon the arrival of the 3rd clock pulse?
Use T flip flops to design a counter with the repeated binary sequence: 0,1,3,5,7. The circuit is to be designed by treating the unused states as don’t care conditions. Sketch the state diagram Derive the state table Implement the circuit.
Design 2-bit synchronous counter that counts 0, 1, 2, 3 in succession. Draw the given counter’s Karnaugh Map(s) of D expressions for each D Flip-Flops (utilizing excitation tables of D flip-flops) for every clock pulse in counting table with indicating every simplification step below.
Given a sequential logic circuit expression asX(t+1) = p'X+pYY(t+1) = pX'+p'Ywhere X and Y are the two flip-flop outputs and p is the main external input.Draw the state transition table for the above-given logic function.Also, draw the state transition diagram associated with it.And What is the behavior of the circuit?
13.For an active low RS FLIP FLOP with a HIGH normal output, the value of its S and R inputs, repectively is ? 14. true or false after simplifying a boolean expression using k map, one should again use boolean algebra to further simplify it