Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allows the digital information from multi-inputs to a single output line

Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allows the digital information from multi-inputs to a single output line

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

a) Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flipflop? A multiplexer (MUX) also known as data selector, is a logic circuit which allows the digital information from multi-inputs to a single output line(b) Design a 8 to 1 multiplexer by using the four variable function given by F (A, B, C, D) = ∑m = (013489 15) (c) OUR school AIT has lockers in all the campus that she often rent them out to students who needs them, upon graduation they are taken back by the school authorities. Kindly express the process of opening this locker in terms of digital operation.
We wish to design a digital system with two flip-flops, say B and C, and one 4-bit binarycounter A, in which the individual flip-flops are denoted by A4, A3, A2, A1. A start signal Sinitiates the system operation by clearing the counter A and flip-flop C, and settling flip-flop B toone. The counter is then incremented by one starting from the next clock pulse and continues toincrement until the operations stop. Counter bits A3 and A4 determine the sequence ofoperations:If A3 = 0, B is cleared to 0 and the count continues.If A3 = 1, B is set to 1; then if A4 = 0, the count continues, but if A4= 1, C is set to 1 on the nextclock pulse and the system stops counting.Then if S = 0, the system remains in the initial state, but if S = 1, the operation cycle repeats.(a) Draw the ASM Chart(b) Draw the equivalent one flip-flop per state
Sketch a diagram of a 4-bit counter with parallel enable logic that counts down from 15 to 0, then resumes counting down form 15 again. use T flip flops.
Design 2 bits counter that count down by using T flip flop when input x =1 and counts upwhen x=0. Find the following1. Derive the state table2. Derive the K‐map simplifications.3. Draw the logic diagram
1. Create the RS Flip-Flop using NAND or NOR Gates (its equivalent circuit) IC.2. Then, use that flip-flop to design an 8-bit register memory using cascaded RS Flip-Flop.3. Use toggle switches for the data and pushbutton switches for storing and clearing the memory.
You are asked to design a synchronous counter that will count the sequence 1 > 2>3>1. (a) Represent these decimal numbers in 2 bits binary numbers. (b) Write down the state table. (c) Find the functions for the next state of the state table using K-map. (d) Draw the circuit (You need to consider D flip-flops as memory unit).
Use T flip flops to design a counter with the repeated binary sequence: 0,1,3,5,7. The circuit is to be designed by treating the unused states as don’t care conditions. Sketch the state diagram Derive the state table Implement the circuit.
Draw a logic diagram of a 4-bit shift register, using D flip-flops, with mode selection inputsS1, S2 to operate according to the following function table: (Please provide actual diagram of the flip-flop circuit)
Using the state transition table below, construct a sequential circuit based on JK Flip flops and any logic gate seen in class. Derive simplified equations for the flip flop inputs as well as for the output Z.
Design SYNCHRONOUS COUNTER using J-K flip flops that counts downfrom 9 to 0.-Show the state and excitation tables for the counter. -Express the flip-flop input functions as a minimal SOP expressions.-. Draw the logic diagram for the counter.
Design a 4-bit Asynchronous forward counter circuit using JK Flip-Flops. Make a logic circuit add-on to the counter that will continue to operate according to an input selection terminal that can operate in Mode-5 or, if desired, Mode-10.
Using T flip flops, Implement a 3-bit asynchronous binary counter.