Design a sequential circuit with two D flip-flops and two input x and y. When x=0, the state remains the same. If x=1 and y=0, the circuit goes through the state transitions 00 to 01 to 10 to 11 then back to 00. When x=1 and y=1, the circuit goes through the state transitions 00 to 11 to 10 to 01 then back to 00. Include state table, state diagram, equation/s from the K-map (flip-flop input equation), and circuit diagram.

Design a sequential circuit with two D flip-flops and two input x and y. When x=0, the state remains the same. If x=1 and y=0, the circuit goes through the state transitions 00 to 01 to 10 to 11 then back to 00. When x=1 and y=1, the circuit goes through the state transitions 00 to 11 to 10 to 01 then back to 00. Include state table, state diagram, equation/s from the K-map (flip-flop input equation), and circuit diagram.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

4) Design a sequential circuit with two JK flip-flops A and B and two inputs Eand F correctly. If E = 0, the circuit remains in the same state regardless of the value of F. When E = 1 and F = 1, the circuit goes through the state transitions from 00 to 01, to 10, to 11, back to 00, and repeats. When E = 1 and F = 0, the circuit goes through the state transitions from 00, to 11, to 10 to 01 and repeats and repeats.
Design a 3-bit up/down counter using positive edge-triggered T flip-flops. Provide a respective timing diagram to justify the design. Show all the relevant working (state table, state diagram, K-maps, state equations, and final circuit diagram). An up/down counter has two inputs say x, y, and a clock signal. The output should increase by 1 if x = 1 and y = 0 on each rising edge of clock and decrease when x = 0 and y = 1 on each rising edge of clock. When x = y, the output should neither increase nor decrease on each rising edge of clock.
Design a 4-bit counter with one external input using T flip flop based on the following sequence: Input=0,6->2->9->13 (repeat), all undesired state go to 2. Input=1, 15->4->12->10 (repeat), all undesired state go to 4? need i) State transition diagram ii) State transition table iii) Simplification using K-Map iv) circuit design ASAP Thanks!
Design a counter with JK flip-flops that counts primary numbers (2,3,5,7,11,13) in loop, show the state diagram, truth table, k-map. Finally draw the circuit.
Detecting and detecting 010011 sequence in binary information received from an external input line xFor sequential logic circuit that makes external z output 1 when it does; a) Create the state diagram. Explain how you created it. b) Create the situation table. Note: D flip-flops are used in this circuit. If not used in the status tableif there are cases, you can specify the next state values and output as neutral values.
A sequential circuit has one input, X. When X = 0, the states of the circuit remain the same. When X = 1, the circuit goes through the state transition from 00 to 10 to 11 to 01, back to 00, and then repeats. (a) Draw the state diagram of the circuit. (b)Draw the state table of the circuit. (c) Derive flip-flop inputs. (d)Draw the circuit diagram.
1. Asequential circuit with two D flip-flops A and B, two inputs, x and y ; and one output zis specified by the following next-state and output equationsA(t + 1) = xy’+ A’y‘B(t + 1) = xB+ B‘+ xB’z = A‘B(a) Draw the logic diagram of the circuit.(b) Draw the corresponding state diagram. 2.A sequential circuit has two JK flip-flops A and B and one input x . The circuit is describedby the following flip-flop input equations:JA = A‘x’+ B’KA = A’+ By’JB = A’+ xB’KB = AB+ xy’z = B‘y‘ + Bx‘y’(a) Draw the logic diagram(b) Draw the state diagram of the circuit.
Consider the following circuit that uses falling-edge triggered D flip-flops. Assume the Clock input, and outputs Q0, Q1, and Q2, are all initially 0. Draw waveforms for Clock, Q0, Q1, and Q2, showing at least ten Clock cycles. A. Write a table summarizing the values of Q0, Q1, and Q2 after each Clock cycle. b. Briefly explain what this circuit does at a high level, treating the Q outputs together.
Design and implement sequential digital circuit, with following specifications: It has one input X, two outputs Y1 and Y0.Whenever an active HIGH is observed at input X at the active clock edge, circuit initiates a sequence and generates output waveforms given in figure below. (After the sequence is completed, it waits for input to be HIGH again) a)Use AND, OR, NOT gates and D type edge triggered flip-flops.Hint: Describe the circuit model Draw the State Diagram Find the State Table Make State Assignment with increasing numbers. (i.e. 0,1,2,3...) Write State and Output equations Draw the Circuit.
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Synchronous Counter Design a circuit of a Synchronous Counter using 74LS76 ( JK-Flip Flop ICs ). The counter should count in following sequence starting from 0. Perform all necessary designing steps by making state table, K-maps and the circuit diagram.
Design a 4 bit asynchronous BCD ripple up counter with a positive edgetriggered JKFlip Flop. You have to include an input named “Count_Down” inyour design. The circuit will work if Count_Down=1 and remain unchanged ifCount_Up= 0.
Digital Circuit Design Design a reverse counter with three D flip‐flops A, B and C. The counter counts from 7, 6, ..., 0, then to 7, and continues. the answer has to include : circuit diagram state equations state table state diagram