Design an interface between a computer and a transceiver. the device's operational concept: 1. Requires a SVDC power supply. 2. A self-driving system that sends a signal from a computer to a transceiver In the device's creation. The components that will be used must be listed by the students. Make a voltage calculation and an analysis of the electronic switching circuit you're using. Students can refer to the topics of rectifier, voitage regulator, and BIT as switches, Report content: 1. List of components in the report 2. Diagram of the Schematic; 3. Analysis 4. The function of each component

Design an interface between a computer and a transceiver. the device's operational concept: 1. Requires a SVDC power supply. 2. A self-driving system that sends a signal from a computer to a transceiver In the device's creation. The components that will be used must be listed by the students. Make a voltage calculation and an analysis of the electronic switching circuit you're using. Students can refer to the topics of rectifier, voitage regulator, and BIT as switches, Report content: 1. List of components in the report 2. Diagram of the Schematic; 3. Analysis 4. The function of each component

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Suppose a power supply is energized by an AC source of 119 V RMS. The transformer step-down ratio is 8:1, it uses a full-wave bridge rectifier circuit with silicon diodes, and the filter is nothing but a single electrolytic capacitor. Calculate the unloaded DC output voltage for this supply (assume 0.7 volts drop across each diode). Also, write an equation solving for DC output voltage (Vout), given all these parameters.
Q18.Determine the values of VCE(off) and IC(sat) for the circuit shown in the figure.
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 18 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 6 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1100 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is..... 2. The value of the dc voltage (Vdc) in volts is..... 3. The value of the ripple factor is..... 4. The value of dc current (ldc) in amperes is..... 5. The value of the output peak voltage (Vpout) in volts is..... 6. The value of peak secondary voltage (Vpsec) in volts is..... 7. The value of primary peak voltage is (Vppri) in volts is.....
Create an objectives when design and creating an AC-DC power supply with selectable output voltage which employs a full bridge rectifier, filter capacitors, and regulators. Create also a schematic diagram.
Explain the process of converting Analgoue to digital converter? Compare the difference in process and 10 applications where we can use ADC and DAC. Also draw the circuit and flow diagram any one type of ADC by hand
Create a schematic diagram for building an AC-DC power supply that uses a complete bridge rectifier, filter capacitors, and regulators and has a selectable output voltage. Keep in mind: When a load is attached, the power supply must be able to deliver at least 500mA of output current.
01. AC system with rated voltage Vs=500kV, to be connected to a 6-pulse rectifier through a transformer with turn ratio r. The DC voltage Vd=250kV, DC current Id=1kA ,the converter equivalent reactance xd=35 ohm, and firing angle is 15⁰, find r=?. If the AC system voltage changes to 525kV or 475kV, what the r1 and r2 will be in order to keep the DC parameters unchanged? 02. The inverter of a 1000MW HVDC project is connected with a 400kV AC system with 120mH equivalent source inductance. Find the SCR. And to describe the strength of the system(strong, medium, weak, very weak?). If the reactive power is compensated by the connection of capacitors with 560MVA, find the ESCR.
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 4. The value of dc current (Idc) in amperes is ? 5. The value of the output peak voltage (Vpout) in volts is ? 6. The value of peak secondary voltage (Vpsec) in volts is ? 7. The value of primary peak voltage is (Vppri) in volts is ?
27. For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 14 volts and V1 is given as 8 volts, compute for the ripple peak-to-peak voltage, dc voltage and ripple factor. If the load resistance has a value of 9 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1300 and N2 is given as 600, compute for the primary peak voltage. 1. The value of the ripple peak-to-peak voltage (Vrpp) in volts is ? 2. The value of the dc voltage (Vdc) in volts is ? 3. The value of the ripple factor is ?
A 6-pulse one connected to the AC network of 50 Hz and loaded with a fixed 120A In a rectifier, what is the average current of a power element in A and what is the transmission time in ms?
Explain the working of Binary Weighted Resistor Digital to Analog converter with a neat diagram. pleas writing not typing
2. Select ONE (1) transducer or sensor with available in the market, with providing the brand, model and technical specification of the selected transducer or sensor, you are required to i. Explain its designed measurand and the working range. ii. Explain its basic working principles and any steps required to take in order to avoid any error (ex. Loading error) during measurement process. iii. Identify either the selected transducer or sensor required a signal conditioner. iv. Propose ONE (1) cable with is suitable to be connected with the selected transducer or sensor