Design Problem: A material is needed to support a hanging sculpture with an overall tensile load of 800 N. It is important that the material not undergo any permanent deformation under this load and must have minimum volume/diameter. Using a circular rod, design structural components using your data for each of the three materials. Which material would you choose for the application and why? If the requirement was minimum weight, rather than minimum volume, which material would you use? Show sample calculations.

Design Problem: A material is needed to support a hanging sculpture with an overall tensile load of 800 N. It is important that the material not undergo any permanent deformation under this load and must have minimum volume/diameter. Using a circular rod, design structural components using your data for each of the three materials. Which material would you choose for the application and why? If the requirement was minimum weight, rather than minimum volume, which material would you use? Show sample calculations.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints. Materials Modulus of Elasticity, (GPa) Yield Strength, (MPa) Tensile Strength, (MPa) Aluminum alloy 70 300 450 Titanium alloy 107 400 550 Steel alloy 207 500 750
When a failure data set for a ceramic material processed in a certain facility is analyzed, it is found that the characteristic strength is 327 MPa and the Weibull modulus is 8.75. A nominally identical batch of material processed in a different facility is also tested and found to have essentially the same characteristic strength, but the Weibull modulus is 6.25. At what stress level is the probability of failure equal to 50% for each set of material? What initial conclusion might you draw about the quality control procedures at the two facilities?
Both yield strength and ultimate tensile strength exhibit the ability of a material to withstand a certain level of load. Which parameter do you prefer to use as a design parameter for a proper selection of materials for structural applications? Explain
Can we design an eccentrically loaded column on the basis of how the bending and axial loads interact?
Advanced hybrid materials technology has been used in automotive applications. A good example is engine block made of aluminum body with cast iron liner as shown in Figure. Please explain its advantages and possible disadvantages
Can the buckling of a column lead to a sudden and dramatic failure of a structure?
A rectangular plate 125 mm long, 10 mm wide, and 3 mm thick is formed from fused silica (aka fused quartz). It is tested in 3-point bending until it fails with a modulus of rupture of 110 MPa at a load of 66 N. Assume the central load point is on the top of the beam. a. How far apart must have been the lower supports? b. What was the maximum stress (magnitude and sign) on the top side of the beam halfway between the centralload point andtheleft-handlowerload point? c. What was the stress (magnitude and sign) directly beneath the central load point exactly 1.5 mm from the top surface? d. If the same plate was tested in pure tension, would the stress at failure probably be higher or lower than measured by 3-point bending? Why?
Explain in your own words how the load test (performance test) is applied to the patient turning apparatus shown in the figure, and guess how the expected result will be. Please answer considering the patient's leg weight and the sponge used in the product.The main part of the product consists of a polyurethane sponge. Stain-proof upholstery fabric will be used as the outer surface material. In addition, there are heating pads working with the logic of electric blankets in this apparatus, please answer by taking these into account when answering.
The figure shown below (Fig. 2) is a schematic representation of a scissor jack in two different positions. The maximum load that this mechanism must withstand is 800 kg. 4 are proposed different materials to make the jack arms and spindle. The mechanical properties and some Physical characteristics of each material are shown in Table 1. a) Based on the properties of each material and the cross section of the arms and the screw, Propose what would be the most suitable material for its manufacture. The length of each arm is 150 mm. The stress on the arms and the spindle must not exceed the yield strength of the material selected for neither of the two analysis positions. b) Using the mechanical properties of the material you selected, calculate the change in dimension that the arms and the spindle of the jack were tested for the two analysis positions. The length of the spindle is 280 mm.
Problem You are tasked with analyzing the frame of a bubble fuselage. The frame is 3D printed using PLA material and must be capable of supporting a 22.05 lb load placed within the cabin space, with the direction of the load indicating the direction of deformation. You will need to perform a series of calculations and analyses to ensure that the design meets strength and safety requirements. Data: Frame Dimensions: A blueprint is provided specifying the dimensions and geometry of the bubble fuselage frame. The thickness of the frame its 0.5 inch. Material: The frame will be 3D printed in PLA material. The material properties of PLA are as follows: Young's Modulus (E): 595669.99 Psi. Yield Strength (σy): 9094.01119 Psi. Density (ρ): 10.04515912 lb/in³ Load: A 22.05 lb load will be applied within the cabin space, with the load direction indicating the direction of deformation Tasks to Perform:( Remmember present the solution process with equations, procedure and results; use…
Problem You are tasked with analyzing the frame of a bubble fuselage. The frame is 3D printed using PLA material and must be capable of supporting a 22.05 lb load placed within the cabin space, with the direction of the load indicating the direction of deformation. You will need to perform a series of calculations and analyses to ensure that the design meets strength and safety requirements. Data: Frame Dimensions: A blueprint is provided specifying the dimensions and geometry of the bubble fuselage frame. The thickness of the frame its 0.5 inch. Material: The frame will be 3D printed in PLA material. The material properties of PLA are as follows: Young's Modulus (E): 595669.99 Psi. Yield Strength (σy): 9094.01119 Psi. Density (ρ): 10.04515912 lb/in³ Load: A 22.05 lb load will be applied within the cabin space, with the load direction indicating the direction of deformation Tasks to Perform:( Remmember present the solution process with equations, procedure and results; use…
Problem You are tasked with analyzing the frame of a bubble fuselage. The frame is 3D printed using PLA material and must be capable of supporting a 22.05 lb load placed within the cabin space, with the direction of the load indicating the direction of deformation. You will need to perform a series of calculations and analyses to ensure that the design meets strength and safety requirements. Data: Frame Dimensions: A blueprint is provided specifying the dimensions and geometry of the bubble fuselage frame. The thickness of the frame its 0.5 inch. Material: The frame will be 3D printed in PLA material. The material properties of PLA are as follows: Young's Modulus (E): 595669.99 Psi. Yield Strength (σy): 9094.01119 Psi. Density (ρ): 10.04515912 lb/in³ Load: A 22.05 lb load will be applied within the cabin space, with the load direction indicating the direction of deformation Tasks to Perform:( Remmember present the solution process with equations, procedure and results; use…