No.DateDeterminationof DischargeThru a-Siphon-Voltormata-(N1)2PI+71;[V2)?P2十名2h= 63.5 cmtrial #1trial #2trial #3t= 75V= 340 mlt- 10sV = 490 mLV: 250mL%3Dcompletetimel3] ' Volume(mL)the table below Ishow calculation pleasc)ActualDischarge(1s)treal#(m)TheorehicalDischargeDifterence

Given Volume, V = 490 mL = 0.49 x 10-3 m3 Time, t = 10 s Find Discharge, Q

Answered: Determaination of Discharge Thru a…

Engineering

Mechanical Engineering

Determaination of Discharge Thru a Siphor Vol tormutai Qo V2 2 (N1)2 ヤユ P2 2g

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fire hose has an inside diameter of 6.5 cm. Suppose such a hose carries a water flow of 40.5 L/s starting at a gauge pressure of 1.68 × 106 N/m2 . The hose discharges through a nozzle having an inside diameter of 3.4 cm. Take the viscosity of water to be 1.005 × 10-3 (N/m2)⋅s dh = 6.5 cmdn = 3.4 cmP = 1.68 × 106 N/m2Q = 40.5 L/s a. the Reynolds number, NR, for flow in the fire hose to show that the flow must be turbulent, with NR≥ 3000. b. Calculate the Reynolds number, NR, for flow in the fire hose and nozzle to show that the flow must be turbulent, with NR≥ 3000.
please answer A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles.( A)What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient η∞ = 1.,(B)In the preceding example; assume a deviation of 10° applied to β2 due to circulation after the modern theory. The flow is 30 lit/s. After drawing/illustrating the velocity diagram, find the theoretical head Ho, in meters, assuming radial flow at inlet, neglecting the deviation in inlet velocity diagram. (c)Assuming that the mechanical efficiency ηmech = 0.95, the hydraulic (or manometric) efficiency ηman = 0.8, find the required break horsepower to drive the pump.
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
A liquid with a specific gravity of 4.7 and a viscosity of 1.3 cp flows through a smooth pipe of unknown diameter, resulting in a pressure drop of 0.183 lbf/in² for 1.73 mi. What is the pipe diameter in inches if the mass flowrate is 5,900 lb/hr?A. 3.64 inB. 0.44 inC. 5.74 inD. 0.005 in
An existing turbine has the following data: D = 95 cm, H = 27 m, Q = 69.9 m3/s, ρ = 998 kg/m3, N = 248 rpm, bhp = 14.1 MW. A new turbine is to be designed based from the existing one to meet the following requirements: H = 91 m and N = 190 rpm. Calculate the new diameter (meter). Round off your final answer to two decimal places.
1) Affinity laws apply to both pumps and turbines. True or False 2) A pelton wheel is used to produce hydroelectric power. The average radius of the wheel is 1.83 m, and the jet velocity is 100 m/s from a nozzle of exit diameter equal to 10 cm. What is the volume flow rate through the turbine in m3/s? a) 263.02 b) 0.801 c) 78.54 d) 0.785 3) A water pump increases the pressure of the water passing through it (see picture below). The flow is assumed to be incompressible. If the outlet diameter is less than inlet diameter, which of the following about outlet and inlet fluid velocity is correct? a) Vout < Vin b) Vout > Vin c) Vout = Vin d) cannot be determined
Water flows through a horizontal pipe of cross sectional of 20 cm2. Atone section, the cross sectional area is 4 cm2. the pressure difference is29.4 psi. How many cubic meters of water will flow out of the pipe in 1min? (can you show the diagram or illustration if possible. thank you!) Choices: a. 0.008 b. 1.208 c. 0.493 d. 0.0185
Note: Don't copy from other experts solution. Read the question carefully and give me right solution with clear calculations. The absolute velocity of a jet of steam impinging on the blades of a steam turbine is 2,200 ft/sec, and that leaving is 980 ft/sec. Assume α1 = 10°, α2 = 155° , u1 = 36 ft/sec, u2 = 72 ft/sec, and r1 =4-inches, r2 = 8-inches. Knowing that the density times flow rate, ρQ = 0.0122 slugs/sec, what is the Power delivered, in HP?
Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
Q 1(a) Use the below given data and calculate the metacentric height. Note: Explain each and every step. w= 200g W=2533.2g Displacement x (mm) 80 60 40 20 0 20 40 60 80 Tilt angle Ɵ (degree) 9.5 7.5 5.5 3 3 5.5 7.5 9.5 M.H (b) By using U-tube manometer how can you find out the pressure head? (c) If you are lacking of equipment, how can you determine the discharge of any channel?
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.1. A schedule-40 pipe necks down from 24 in at point A to 12 in at point B. 8 *3/sec of 60°Fwater flow from point A to point B. The pressure head at point A is 20 *. FricLon is insignificantover the distance between points A and B. What are the magnitude and direcLon of theresultant force on the water? (A) 2900 lbf; toward A(B) 3500 lbf; toward A(C) 2900 lbf; toward B(D) 3500 lbf; toward B
A pump 254 mm suction pipe and a 127 mm discharge pipe is used to deliver 52 L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 100 cm above the suction gage which reads reads 108 kPa gage. Determine the following: 1. The total dynamic head in meter 2. The water power in kW 3. The motor horsepower if the pump efficiency is 76% Choices: 1. 13.856 14. 495 14.409 2. 7.631 7.348 8. 245 3. 12.960 14.935 13.935