Answered: Determine Pa-PB if x = 3.0 m, y = 1.0…

Determine Pa-PB if x = 3.0 m, y = 1.0 m, z = 2.5 m in the figure below. Fluid 1 and 3 is paraffin, fluid 2 is water. Use S.G for paraffin as 0.8.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Related questions

Q: Find the capillary rise ( h) in the tube shown in the figure for a water-air-glass interface with =…

Q: ording to Figure (1) below, the pressure at point 2 is..... the pr t1 2 Equal to 50 m 150 m

A: Ans: greater than

Q: The system in the figure consists of AB copper bars with a diameter of 30 mm and BC aluminum bars…

Q: Problem 3: A length of clear plastic tubing is bent into a vertical U, as shown in the figure, and…

A: Given data A U tube has two immiscible liquids A and B. liquid A has density ρA and height d1 in the…

Q: A bar of circular cross section is to suspend a tank of water 4 ft. below a ceiling. The tank can be…

Q: The pressure vessel shown.above is made from 4 mm thick steel plate. A pressure of 3.5 MN/m² is…

Q: A trough with a trapezoidal cross-section, as shown in the figure, contains vegetable oil with…

A: Given: Density of the vegetable oil→ρ=940 Kgm3 Acceleration due to gravity→g=9.8 ms2 (a): Because…

Q: Problem 6: A cube with edges of length L = 0.23 m and density g. = 3.2x10³ kg/m³ is totally…

A: Length of the cube, L= 0.23 m Density of the cube, ρc= 3.2×103 kg/m3= 3200 kg/m3 Density of the…

Q: a. A spherical container of diameter 2 × (Z + 50) m having a chemical is kept at 300 m below from…

Q: In figure below pressure gage A reads 1.5 kPa (gage). The fluids are at 20 °C. Determine the…

Q: Find the surface tension of a droplet whose inner pressure is 0.075 psi more than the atmosphere…

A: Answer: The surface tension of a droplet is 0.0068 lb/ft. Hence, the correct answer is option (a).

Q: The piston shown in figure is held in equilibrium by the pressure of the gas flowing through the…

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

Q: 3) A steel ball was put in a dense liquid medium where the pressure is 70 MPa. If for this steel…

Q: Example 4-6: The water flows through the pipe bend with a discharge of 200Ls. The bend is placed…

A: To Find: The magnitude and direction of the force of water on the bend. Given : The discharge is…

Q: A research-type submersible with remote TV monitoring capabilities and weighing 35 200 N, was…

A: Given data weight = 35 200 N depth = 646 m an area = 452 x 10-6 sq.m E = 200 GPa To…

Q: An isosceles triangle gate AB (in the figure below) is hinged at A and weighs 1500N. What is the…

Q: 3 Water is supported by a curved gate described by equation y=-x'. The gate is 5 supported with a…

Q: M M M M L- 5e FIG. 2. Problem 2 Find D in the above figure in terms of 0, and L.

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a…

Q: DOL V 12 A light elastic cord of length lo = 5.0 m and stiflness k= 50 N/m is inside o fixed box…

Q: 1. A building is 512 m high. What must be the minimum water pressure (psi) in a pipe at ground level…

A: As per guidelines i can solve only 1st question. Given data; height = 512 m Neglect friction loss…

Q: 1. A rope holds up a rectangular, hinged gate, as shown in the figure. Derive expressions for the…

A: For solution refer below images

Q: This problem uses Figure 1 .Consider a flat plate of thickness h submerged in a liquid of density…

Q: 10. A thin – walled spherical tank is filled with water at a pressure 4666 psig. The tank's volume…

A: Pressure, P1= 4666 psig Volume, V1= 805.407 in3 After the water is released form the tank, the…

Q: L1 = 12.0 cm L3 = 5.0 cm Oil L2 10.8 cm Water Problem 2: A glass tube containing oil is inserted…

A: Given data as per question

Q: T トヒ

Q: The piston shown in figure is held in equilibrium by the pressure of the gas flowing through the…

A: Consider the free body diagram of the piston as shown below.

Q: For all additional Problem: Piston The piston shown in figure is held in equilibrium by the pressure…

A: Given PI=350kPa PII=130 kPa PIII=210 kPaForce on piston due to PI,…

Q: The piston shown in figure is held in equilibrium by the pressure of the gas flowing through the…

A: Draw the free body diagram of the piston and indicate the various forces acting on it:

Q: A droplet with an inner pressure that is 0.075 psi higher than the air has a diameter of 0.03…

Q: A garden hose is positioned as shown in the figure with its open end (#2) is h=2.8 above the faucet…

A: Consider the faucet end as end 1 and open end as end 2. Use continuity equation between ends 1 and…

Q: Find the capillary rise (h) in the tube shown in the figure for a water-air-glass interface with O=…

Q: In the figure, a cube of edge length L = 0.556 m and mass 1200 kg is suspended by a rope in an open…

A: GivenL=0.556 mm=1200kgDensity=1.03E+3 kgm3h=L2=0.5562=0.278mPO=atmospheric pressure=1 atm=1.01×105…

Q: side a vacuum chamber. The chamber is isolated from the nvironment by a piston, which is free to…

A: Givenk=1250N/md=12mmP=1atm=101325PaD1=4mx2=17.325mm

Q: Consider a system of two springs, with stiffnesses k1 and k2, arranged in parallel as shown in the…

Q: ll standpipe as shown in Figure Q1(a) with an open top has an inner diameter d = 21 m and wall…

A: Given:d=21 mt=25 mmγ=9.81 kN/m3σc=12 MPa

Q: A plastic spherical balloon is held below the surface of a swimming pool by a cable tied to a…

A: Given data Volume of sphere (V) = 1.5×10^-2 m^3 Tension in cable (T) = 90 N

Q: Po d -L- Pw

Q: The hydrostatic force on the gate and its position as function of h and show its direction on the…

A: Data given - d = 1 m h = 2.5 m b = 2.2 m Density of water = 1000 kg/m3 g = 9.81 m/s2 As per…

Q: If Eg = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a…

A: Given: bulk modulus = 2.2 GPa dv/v = 6%

Q: Find the Tensions TCA and TcB for the system as shown in figure. Take P = 140 mm, Q= 220 mm, 0 =…

Q: The gauge pressure in the air container illustrated in the figure is 80 kPa. Calculate the…

Q: A tall standpipe as shown in Figure Q1(a) with an open top has an inner diamet d = 2.1 m and wall…

A: Given:d=2.1 mt=20 mmγ=9.81 kN/m3σc=12 MPa

Q: direction, as shown in the figure. The cylinder is 50% filled with water (the shaded part), with…

A: An infinetely lengthy tube shaped compartment roughage a cross segment area of sweep R and is set…

Q: The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction…

A: Given Data The thickness of the plastic panel is:t=3mm=0.003 m The weight of the plastic panel…

Q: A storage tank contains oil and water as indicated in the figure. At the point where the two liquids…

Q: Uniform bir kesite sahip, ince bir çelik tel, şekilde görüldüğü gibi bükülmüştür. Oluşan cismin…

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

Kindly answer correctlly. Show all the necessary steps

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fluid having a density of 1400 kg/m³ stands in a tube of 6 mmθ at a height of 27 mm. what is the true static height? use surface tension equals to 0.1052N/m and contact angle is 15degrees.
Using Laplace equation figure out how higher than atmospheric pressure is the inner pressure in a drop of water of radius 3 mm interfacing air at atmospheric pressure. Water surface tension 0.072 N/m. Atmospheric pressure 1.01x105 Pa.
The density of a fluid is given by the empirical equation: ? = 70.5exp(8.27×10^−7 ?), where ? is density (lbm/ft^3) and P is pressure (lbf/in^2). a) Calculate the density in g/cm^3 for a pressure of 9.00 x 10^ 6 N/m^2.c) Derive a formula for ? (g/cm^3) as a function of P (N/m^2).
Steam at 200 psia and 500°F flows at 100 fps in a 4 inches pipe inside diameter. What is the surface coefficient on the inside of the pipe if the thermal conductivity is 0.255 Btu-in/ft2-hr-°R, Cp = 0.559 Btu/lbs-°R, absolute viscousity is 1.2 x 10-5 lbs/ft-sec and specific volume is 2.725 ft3/lbs. Show your complete solution.
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution. (Please write legibly, I did not understand the first solution.)
Show complete solutions with figures Compute the capillary depression of mercury at 68oF ( θ = 140o) to be expected in a 0.05-in diameter tube. For mercury σ = 0.032 lb/ft and ρ = 26.3 slug/ft3 a) 0.333 inches b) 0.712 inches c) 0.215 inches d) 1.025 inches e) none.
The fluid in Figure 58 is CO2 at 20 ° C. Neglect losses. Say p1 = 179 kPa and the pressure gauge fluid is Merian red oil (S = 0.827), estimate (a) p2 and (b) the gas flow in cubic meters per hour.
Please write down Darcy’s law with pressure and potential form separately, explain the meaning of each parameter and list their unit.
Give me right solution with clear calculations. A closed cylindrical tank 1.89m high and 0.99m in diameter contains water of height 1.35m. When the angular velocity is constant at 20rad/sec What is the area (m 2) uncovered at the bottom? A. 0.1 B. 0.3 C.0.7 D. 0.07 If it is rotated at 15rad/sec and the air has a pressure of 200kPa what is the minimum pressure at the bottom of the tank in KPa? A. 245.10 B.145.10 C.201.45 D.210.54
Find the surface tension of a droplet whose inner pressure is 0.075 psi more than the atmosphere having a 0.03 in diameter a. 0.0068 lb/ft b. 0.0054 lb/ft c. 0.0072 lb/ft d. 0.0081 lb/ft
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
A cylindrical tank shown below has a radius ? and a circular orifice at the bottom of radius ?. At time ? = 0 the liquid level in the tank is ho. (a) Use the Bernoulli equation to determine the relations between the orifice velocity ?o and the free surface velocity ?s (assume the surface velocity is not zero). (b) Use conservation of mass to determine the orifice velocity in terms of the free surface velocity. (c) Use the results in (a) and (b) to derive a differential equation for h(?). Note that ?s = − dh/dt. d) Separate variables and solve the equation for h(?) with the initial condition h(0) = ho (e) Determine how long it will take to empty the tank.