Determine the allowable load capacity of the 0.4 m diameter pile shown in Figure 4. The fill is new and unconsolidated. A steel shell is proposed around the pile within the fill layer to eliminate the negative friction. The ground water level is at the middle of the fill layer. Use a factor of safety of 2.5. (y=moist unit weight; ysat=saturated unit weight)

Determine the allowable load capacity of the 0.4 m diameter pile shown in Figure 4. The fill is new and unconsolidated. A steel shell is proposed around the pile within the fill layer to eliminate the negative friction. The ground water level is at the middle of the fill layer. Use a factor of safety of 2.5. (y=moist unit weight; ysat=saturated unit weight)

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.7P

See similar textbooks

Similar questions

A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Determine the maximum load that can be allowed on a 450 mm diameter driven pile shown in Figure P12.6, allowing a factor of safety of 3. Use K = 1.5 Ko and = 0.65 in computing the shaft load. Use Meyerhofs method for computing the point load.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure 18.36, with a safety factor of 3. Use the a method for computing the shaft friction. FIG. 18.36
Redo Problem 12.20 using Vesics method, assuming that the skin friction is distributed uniformly along the shaft. 12.20 A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
A 400-mm diameter and 15 m long concrete pile is driven into a sand where = 18.0 kN/m3 and = 31. Assuming = 0.65 and K = 1.4 Ko, determine the load carrying capacity of the pile with a factor of safety of 3.
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Redo Problem 12.3 using Coyle and Castellos methods for estimating both Qp and Qs. 12.3 A 500 mm diameter and 20 m long concrete pile is driven into a sand where = 18.5 kN/m3 and = 32. Assuming = 0.7 and K = 1.5 Ko, determine the load-carrying capacity of the pile, with a factor of safety of 3. Use Meyerhofs method [Eq. (12.18)] for computing the point load-carrying capacity Qp, and Eqs. (12.42) and (12.43) for computing the load-carrying capacity of the pile shaft Qs.
Determine the ultimate load capacity of a circular pile with diameter D = 20 cm installed in asaturated soft clay. The pile is embedded 10 m into the ground. According to measurements, thesoil exhibits an undrained shear strength according to the linear relationship: Su = 2+1.6z, wherez is the depth in meters and Su is the undrained shear strength in kPa. The soil's unit weight canbe assumed as 18 kN/m3
For the pile distribution below, determine the load Pp that the red pile will receive, in Ton. P = 254 Ton, d = 2 m, ex = 0.2 m, ey = 0.3 m, H = 1.3 m. ex, e and positive with the axes. Consider the self-weight of the head.