Determine the amplitude and phase shift of the sinusoidal ouput of the circuit shown below, if a sinusoidal input of frequency 790 rads/second and amplitude 10 volts is applied to the circuit. Add the phase shift to the amplitude and enter the result in the answer field (numerical answer only). Component values are R = 7360 Ohms; C = 5.96e-06 Farads; L = 0.00501 Henrys; C B H 0000 R Vout

Determine the amplitude and phase shift of the sinusoidal ouput of the circuit shown below, if a sinusoidal input of frequency 790 rads/second and amplitude 10 volts is applied to the circuit. Add the phase shift to the amplitude and enter the result in the answer field (numerical answer only). Component values are R = 7360 Ohms; C = 5.96e-06 Farads; L = 0.00501 Henrys; C B H 0000 R Vout

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.9MCQ

See similar textbooks

Similar questions

When you are converting an instantaneous current to a phasor, how does the phase angle being positive or negative affect solving the problem i.e. the representation being (wt - the phase angle in degrees) or (wt + the phase angle in degrees)?
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
Between i1 = -30cos(ωt + 50°) and v1 = 24sin(ωt - 10°), calculate the phase angle. Sketch and state which sinusoid is leading.
Relative to the reference sinusoid, what is the phase angle of i, vR and vL in degrees?
The signal V1=100 cos(500t - 30°) and the signal V2=20 sin (500t +45°) compared in phase would be
Draw the phasor and wave diagram of the following sinusoidal current: I1 leads I2 by 350, I4 leads I3 by 450, I5 lags I2 by 350, I3 lags I1 by 200. Use I5 as reference. RMS values of current are all equal to 40 A.
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram and question. please answer it based on your knowledge. thank you so much!)
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by (a) 1202cos(t+60) (b) 120cos(t+60) (c) 1202sin(t+60)
Using the data in Table 1.1 convert the current I and source voltage Vs to RMS values. Then draw a plot of the power phasor diagrams at a frequency of 1000 Hz and another at a frequency of 8000 Hz. Determine the real power, the reactive power, and the apparent power in the RC circuit at those frequencies.
Find the ff. on the AC circuit below having a 120Vrms as a signal source V1. a.) Total Impedance ZT b.) Current Ic , IL & IR c.) Current Total IT d.) Phasor angle e.) Voltage across each branch. VR, Vc, VL f.) Draw the phasor diagram of the circuit with complete label. g.) Plot the sinusoidal wave indicating the phase angle, showing which are lagging or leadingNote: (see attached image for the diagram. please answer it based on your knowledge. thank you so much!)
Suppose we are to convert the phasor current I(jw) to the sinusoidal current i(t). Which of the following statements is/are true? The magnitude of the phasor current I(jw) is equal to the amplitude of the sinusoidal current i(t). The magnitude of the phasor current I(jw) is equal to the effective value of the sinusoidal current i(t). The angle of the phasor current I(jw) is equal to the phase shift of the sinusoidal current i(t). a. 2 and 3 b. 1 and 3 c. 2 only d. 1 only