Determine the dead weight of the reinforced concrete T-beam bridge interior beam using Figure 26 and the bridge data given: Span length Minimum yield strength of steel 0.03 ksf , Barrier (curbs and parapets) load = o.505 klf 50 ft, Beam spacing= 10 ft, Concrete strength = 4.5 ksi, = 60 ksi, Future wearing surface load= %3D

Determine the dead weight of the reinforced concrete T-beam bridge interior beam using Figure 26 and the bridge data given: Span length Minimum yield strength of steel 0.03 ksf , Barrier (curbs and parapets) load = o.505 klf 50 ft, Beam spacing= 10 ft, Concrete strength = 4.5 ksi, = 60 ksi, Future wearing surface load= %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Structural steel buildings frequently are designed with diagonal bracing systemsto resist lateral loads (horizontal forces resulting from wind or earthquakeloadings).A certain bracing system is subjected to the following loads:dead load = 13.5 kipsoccupancy live load = 6.8 kipsroof live load = 1.4 kipssnow load = 1.4 kipswind load = 150.5 kipsearthquake load = 161.2 kipsa. Determine the required factored load capacity for LRFD. Which AISC loadcombination controls?b. Determine the required ASD load capacity. Which AISC load combinationcontrols?Note: All given loads are service loads.
A concrete block is supported by two guy wires attached to an anchor ring as shown. a.Determine the resultant force on the anchor ring. b.Angle of the resultant force with respect to the horizontal axis. c.Weight (W) of the concrete block with a factor of safety of 1.25 to prevent uplift.
a. Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression. b. If the beam will carry the loading pattern shown in Figure 1(b), what safe load Wcan it carry based on the design moment in part (a)?
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
Explain how your answer to the problem below affects the design of a structure. Explain how the required tension steel area affects the design of a structure. Problem: A rectangular beam has b = 300 mm and d =490 mm. Concrete compressive strength is 27 MPa and steel yield strength is 276 MPa. Calculate the required tension steel area if the factored moment is (a) 20 kN-m, (b)140 kN-m, (c) 485 kN-m, and (d)520 kN-m.
A slab with L/S = 2.50 has a thickness of 150 mm reinforced with 12 mm - diameter deformed bars at spacing s = 200 mm on center. Assume f'c = 28 MPa and fy = 415 MPa. Use clear cover of 20 mm. What is the safe live load in KN/m it could carry if L = 5 m? Express your answer in two decimal places. please give answer in text form
Design testing and detection scheme for bridge bearing capacity, illustrate the equipment and materials used in the testing.
Question 2: Figure 2 shows the beams layout of a reinforced concrete building. The concrete compressive strength, f_{c} = 28MPa and the reinforcing steel yielding strength, f r =420MPa. Beam B2 has a rectangular cross section of width, b = 450mm and thickness, h = 450mm with effective depth, d = 390mm and Beam B1 has a rectangular cross section of width, b = 450mm and thickness, h = 1000mm with effective depth, d=900mm. The slab has a thickness, h = 250mm with effective depth, d=200mm. The slab is subjected to superimposed dead and live loads of 5.0kN / (m ^ 2) and 6.0kN / (m ^ 2) respectively in addition to its self-weight. The slab is reinforced with flexural bottom bars of Ø16/150mm. Check the slab to carry the applied loads.
Given a simply supported reinforced concrete slab with the effective span lo=2.8 m. The slab is 90 mm thick and reinforced by $10@200 longitudinal bars. The material properties are f= 11.9 N/mm², f= 1.6 N/mm². fy=280 N/mm, and E, = 2.0 x 10 N/mm². Calculate the maximum load (per square meter) that the slab can sustain.
The steel framework shown below is used to support the reinforced concrete slab (unit weight of concrete =23.6KN/m3) that is used for an office use (minimum live load = 2.4KPa). The slab is 150 mm thick. Use a=3m, b=5m. Neglect the self-weight of the beam and girder. Assume all beams and girders have simple supports. NSCP 2015 Load factors: 1.2DL & 1.6LL. Calculate the total ultimate/factored SLAB load in Kilo Pascals? Express your answer in 2 decimal places.
A simply supported beam has a maximum moment equal to 22 KN.m. The beam has a width of 200 mm and a depth of 250 mm and is made up of 80% grade Narra. Use dressed dimension by reducing its dimensions by 10 mm. What is the actual bending stress of the beam in MPa?
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa