Determine the deflection at D using AREA MOMENT METHOD E = 200 GPa, IAB = 250x10° mm“, IscD = 200x10° mm'. Distances are in meters. Show completeSolutions8 kN6 kN15 kN/mOC DhangeA34Technology Druen by (nnovationFRJALAANG n TRCHInput your answer in two decimal places. Units in millimeters. No need to write down the units. Just input the numerical valuewith the sign. Example: if your final answer is 2.11mm upwards, just key-in 2.11 then if your final answer is 2.11mm downwards,key-in -2.11

Answered: Image /qna-images/answer/08df6c27-06d3-4ea9-8bc3-8337714da0ea.jpg

Answered: Determine the deflection at D using…

Engineering

Civil Engineering

Determine the deflection at D using AREA MOMENT METHOD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 16 kN 20 kN 30 kN/m F D B. C 2m 4m 4 m 3 m Which of the following most nearly gives the reaction (KN...

A: As per company's guideline , we can only answer first three questions Kindly post other question as...

Q: hydrostatic

Q: What is the significance of learning isometric and orthographic projections as a civil engineering s...

A: Significance of isometric and orthographic projection in Civil Engineering.

Q: Determine the force in member DJ. 2) With a roller support at G and a pin support at A, find the ver...

Q: A simply supported one way reinforced concrete floor slab has a span of 3 m. It carries a service li...

Q: Compute the area of cross-section if the formation width is 12 m, side slopes are 1 to 1, average he...

Q: For the illustrated plain concrete T-beam, compute the stress at top and bottom of the extreme ...

Q: 1. The plate below is attached to the vertical surface AB. Its top and bottom surfaces slide smoothl...

Q: Not interested in the calculations, just want to see the graph so please display that for me instead...

A: Given. Initial height (H) = 14.31 mm Sample area (A) = 2827.433 mm2 or 28.27 cm2 Dry weight (Ws) = 5...

Q: A sample of moist clay is found to have a moisture content of 400 and degree.of saturation of 85%. T...

A: s= degree of saturation = 85 % =0.85 G= specific gravity = 2.76 w= moisture content =400 % =4 e= voi...

Q: 10 lb 25 lb 15 lb 1 ft

Q: Calculate for the shear force in kN at member ED of the frame shown in figure 1 using Portal Method....

Q: Define the major losses and minor losses in pipe flow.

A: MAJOR LOSSSES ARE DUE TO FRICTION AND MINOR ARE DUE TO VARIOUS REASONS

Q: 40 k F 20 k 5 ft D E 5 ft C В -5 ft- -5 ft- -S t- -5 ft- Determine the Vertical Reaction at A.

A: This question is related to the Structure Analysis. In this question we calculate the vertical react...

Q: As you can see on this equipment, an Engineer design a belts/pulley with 0.03m shaft and a shear key...

A: Given: Required to find: The value of shear stress τ.

Q: nere are two (2) mercury barometers at the mountain. At the top reads 500 mm and at the base reads 6...

A: To find the height of the mountain (H)-

Q: An old equal-tangent crest vertical curve was designed with a PVI at station 117+45 and elevation of...

A: An equal tangent crest vertical curve is as below The point PVC is called as the initial tangent po...

Q: Determine the horizontal and vertical components of reaction at the pins A and C. JA 12 kN/m 60° -60...

A: This question is related to the Structure Analysis. In this question we calculate the reaction at su...

Q: he recommended steel ratio for a slab having thickness of 125 mm is 0.00215 determine the required a...

A: Steel ratio is Ast/BD

Q: Calculate the force in member IJ. 15 KN 10 KN 10 KN 20 KN A В E 5.0 m 4 @ 3.0 m = 12.0 m

A: Use method of joints

Q: Determine the moment arm of the resultant relative to the origin O. Each space is 1 foot

A: To determine the moment arm of the resultant force w.r.t. O. The moment arm can be obtained from: ...

Q: total

A: The total column moment in a storey are equivalent to the product of storey shear and half the heigh...

Q: For a given soil, the void ratio e, water content w, and specific gravity Gs are found to be 0.50, 1...

Q: steel structure is loaded as shown. h. = 4 m, L = 3m, P = 40 KN, E = 200 GPa, ==100x10 ch of the fol...

Q: Given in the accompanying tabulations are the observed forward and back bearings of a closed compass...

Q: redius af the tube (8)= 2mm = 2X10 m Surface tenstom () = 0-752N|m wetting angle (0) = 130° %3D To f...

A: To find : The value of surface tension=0.752 N/m The value of wetting angle=130∘ The value of radius...

Q: A given soil sample is taken from the field by Bubba Lesh for compaction testing. Before compaction,...

A: solutioncompaction is defined as removal of air from the soil present in the voids compaction is don...

Q: Y 8 - 200 450 mm d' = 35 mm

A: Given data: fy=460 N/mm2d'=35 mm

Q: leans against the floor at A making an angle of 45° with the horizontal. The gate to be opened from ...

A: solutionWeight of gate, W =600lbWidth of gate, B =20ftAngle of gate with horizontal, θ =45°Specific ...

Q: A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm d...

Q: eom/coune/1361/qui/ aloustions/2101 E 20 k 12 12 ft 5 k 5 ft-5 ft-- -14 ft

Q: triangle of height h and base b is vertically submerged in a liquid. The base b coincides with the ...

Q: Calculate for the shear force at member FE in kN of the frame shown in figure 1 using Portal Method....

Q: Discuss why the friction factor is independent to very large Reynolds numbers

Q: The center height of the road at station 7 + 110 is 2m fill while at station 7 + 160 it is 1.2m cut....

Q: The bearings of forward and backward tangent are N 65°30’ E and N 75°40’ W, respectively. If the de...

Q: fundamentals of surveying. DEFLECTION ANGLE TRAVERSE. The following are the measured deflection ang...

A: Solution The following are the measured deflection angles for a closed traverse: 97° 05’ R, 152° 1...

Q: O Camidee the hemepleeced spiedl Shown bebw Bubged G Q eidlial staess p (cum forun). Computi the Vee...

Q: Direction: solve and analyze each of the folle 1. The population of a certain community fol 100,000 ...

Q: 15 KN/m 1. The beam shown in the figure carries distributed loads. Design the square (a x a) cross-s...

Q: Find the reactions at the fixed connection at A. 4 N/m v v v V 2m 4m A O RA = 16N; MA = 32N. m count...

Q: COLUMD IN PROBLEM 4, ASSUMING THE RALLY BRACED ABOUT THE Y-Y AXIS AUP ĐEURE

A: solution Step - 1 : calculate the required strength LRFD ASD Pu = 1...

Q: Find the radius R of the simple curve so that the curve will pass through a point which is 30m from ...

Q: A load of 800 Kip will be distributed on a circular foundation with a diameter of 20 feet, this stru...

A: Given:- The magnitude of the load on the column = 800 kip The diameter of the circular foundation = ...

Q: Calculate the cracking moment (Mcr) for the plain concrete. Assume normal-weight concrete and f’c...

A: Given: The value of f’c is 4000 psi. Consider the figure,

Q: fundamentals of surveying. CLOSED COMPASS TRAVERSE. Given in the accompanying sketch are the observe...

A: We have to adjust the observed direction and tabulate accompanying sketch observed forward and back ...

Q: Calculate the depth of the neutral axis of the section in PART A in mm.0 Calculate the ultimate mom...

Q: A differential manometer is attached to a pipe as shown in figure below. Calculate the pressure diff...

Q: A 100-ft long dam holds 30 ft of water as shown in the figure. L= 100 ft. w.s. 30 ft. 609

Q: Show that F f | gL _H when resistance force (F) for a boat has related with a function of length L, ...

A: solutionUse buckingham pi theoremGiven parameteres Resisting force F; Length L; VelocityVacceleratio...

Concept explainers

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.

Question

Determine the deflection at D using AREA MOMENT METHOD

E = 200 GPa, IAB = 250x10° mm“, IscD = 200x10° mm'. Distances are in meters. Show complete
Solutions
8 kN
6 kN
15 kN/m
OC D
hange
A
3
4
Technology Druen by (nnovation
FRJALAANG n TRCH
Input your answer in two decimal places. Units in millimeters. No need to write down the units. Just input the numerical value
with the sign. Example: if your final answer is 2.11mm upwards, just key-in 2.11 then if your final answer is 2.11mm downwards,
key-in -2.11

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

GIVEN DATA

VIEW

REACTION & I DETERMINATION

VIEW

DEFLECTION DUE TO 6KN LOAD

VIEW

DEFLECTION DUE TO UDL LOAD

VIEW

DEFLECTION DUE TO 8KN LOAD

VIEW

DEFLECTION DUE TO Rc LOAD

VIEW

FINAL DEFLECTION AT D

VIEW

Step by step

Solved in 7 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hello can you help me with this problem? The value of P is 45Kips
Type in your answer/s rounded off to 2 decimal places except for whole numbers. (ex: 10.67, 28, 732.40) If your answer is 120.00 kN, just write 120 kN Do not round off values during solving. Use the store function of your calculator or its fraction if applicable. Include the units specified after your answer. Leave a space between the value and the unit. (ex: 6323.17 m, 73.10 lb-in, 100 kN)
Answer the problem question, use 2 decimal places as final answer ( Examples of 2 decimal:21.045 write as 21.05 ) The final answer should be boxed. Don't forget the unit. Write it on paper, showing the correct answer and solution.
Use the unit meter (m)
Thumbs Up will be giveb if answered. Solve in 3 decimal places.
No rounding off in the solutions. Use g=9.81 m/s2, g=32.2 ft/s2. 4 DECIMALS please
Solve as soon as possible like 5 minutes thsnk you
Find Q, and I. Q is using Q=Ay. Please help i am very lost. For Q i get 69.8 and for I 19,750.
Hello I'd like to ask asnwer for this problem. The value of P is 45
Show the details of your solution. Three decimals.
UPVOTE will be given! Please write the complete solutions legibly. No long explanation needed. Answer in 2 decimal places. Dynamics of Rigid Bodies The rotation of the 0.9-m arm OA about O is defined by the relation Eq. (1), where is θ expressed in radians and t in seconds. Collar B slides along the arm in such a way that its distance from O is Eq. (2), where r is expressed in meters and t in seconds. After the arm OA has rotated through 30°, determine the relative acceleration with respect to the arm (m/s2).(Answer in 2 decimal places) θ = 0.15t2 is Eq'n (1) r = 0.9 - 0.12t2 is Eq'n (2)
UPVOTE will be given! Please write the complete solutions legibly. No long explanation needed. Answer in 2 decimal places. Dynamics of Rigid Bodies The rotation of the 0.9-m arm OA about O is defined by the relation Eq. (1), where is θ expressed in radians and t in seconds. Collar B slides along the arm in such a way that its distance from O is Eq. (2), where r is expressed in meters and t in seconds. After the arm OA has rotated through 30°, determine the acceleration (m/s2).(Answer in 2 decimal places) θ = 0.15t2 is Eq'n (1) ; r = 0.9 - 0.12t2 is Eq'n (2)