2.75 plz 2.75 The plastic block shown is bonded to a rigid support and to a verti-cal plate to which a 55-kip load P is applied. Knowing that for theplastic used G = 150 ksi, determine the deflection of the plate.3.2 in.2.76 What load P should be applied to the plate of Prob. 2.75 to producea 16-in. deflection?2.77 Two blocks of rubber with a modulus of rigidity G = 12 MPa arebonded to rigid supports and to a plate AB. Knowing that c = 100 mmand P = 45 kN, determine the smallest allowable dimensionsa and b of the blocks if the shearing stress in the rubber is not toexceed 1.4 MPa and the deflection of the plate is to be at least 5 mm.4.8 in.2 in.Fig. P2.75

Given P=55 kip G=150 ksi To determine: The deflection of the plate

Answered: determine the deflection of the plate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 4-ft section of aluminum pipe of cross-sectional area 1.75 in2 rests on a fixed support at A. The 58-in.-diameter steel rod BC hangs from a rigid bar that rests on the top of the pipe at B. Knowing that the smodulus of elasticity is 29 3 106 psi for steel and 10.4 3 106 psi for aluminum, determine the deflection of point C when a 15-kip force is applied at C.
The plastic block shown is bonded to a rigid support and to a vertical plate to which a 55-kip load P is applied. Knowing that for the plastic used G= 150 ksi, determine the deflection of the plate
The plastic block shown is bonded to a fixed base and to a horizontal rigid plate to which a force P is applied. Knowing that for the plastic used G = 55 ksi, determine the deflection of the plate when P = 11 kips. The deflection of the plate is in.
The length of the 332332 -in.-diameter steel wire CD has been adjusted so that with no load applied, a gap of 116116 in. exists between the end B of the rigid beam ACB and contact point E. Knowing that E = 29 × 106 psi, determine where a 57-lb (w) block should be placed on the beam in order to cause contact between B and E. For contact, x < in.
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that Es5 200 GPa and Eb5 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C.
A steel loop ABCD of length 5 ft and of 3838 -in. diameter is placed as shown around a 1-in.-diameter aluminum rod AC. Cables BE and DF, each of 1212 -in. diameter, are used to apply the load Q. Knowing that the ultimate strength of the steel used for the loop and the cables is 75 ksi, and that the ultimate strength of the aluminum used for the rod is 45 ksi, determine the largest load Q that can be applied if an overall factor of safety of 3 is desired. The largest load Q that can be applied is kips.
Figure 4 shows two solid cylindrical rods and joined at B. The rod ABC is made of an aluminumfor which E = 70 GPa. Knowing that P = 6 kN and Q = 42 kN, determine the deflection of;a) Point Ab) Point B
Both portions of the rod ABC are made of an aluminum for which E = 70.4GPa. Knowing that the magnitude of Q is 31876 N, m = 0.35 m, and n = 0.55 m, determine the value of P (in N) so that the deflection at A is zero.
The rigid bar AD is supported by two steel wires of -in. diameter (E = 29 x 10 psi) and a pin and bracket at D. Knowing that the wires were initially taut, detemine (a) the additional tension in each wire when a 120-1b load P is applied at B. (6) the corresponding deflection of point B.
A single axial load of magnitude P is applied at end C of the steel rod ABC. Knowing that E = 30 × 106 psi, the deflection of point C will be 0.1 in. Determine the diameter of portion BC in inches if P = 50 kips.
A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used, τall= 220 psi and G= 1800 psi. Knowing that a centric vertical force of magnitude P=3.2 kips must cause a 0.1-in. vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block
Fbd ,formula and calculation should be included. Please work it fast without wasting a time. 1)The rod ABC is made of an aluminum for which E = 70 GPa. Knowing that P = 9 kN and Q = 14 kN, determine the deflection of: (a) Point A, (b) Point B. Consider upward to be positive.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS