Answered: Determine the force in each cable if F…

Engineering

Mechanical Engineering

Determine the force in each cable if F = 500 lb. Ans: FAC = 113 lb FAB = 257 lb FAD = 210 lb %3D 1ft 6 ft 2 ft 3 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Related questions

Q: B E 1 4 m 4 m C A 3 m 3 m D 3 Consider the problem sketch. Ignoring the supports, the sketch…

A: In this problem, it is asking for the number of two-force members in the sketch. Two-force member is…

Q: Q/ Find the force just in members BD, CD and CE? 3 m 4 m 3 m 3m 3 m 3 m 3 m 30 kN 30 kN 90 kN

Q: below. 1. Find the zero-force members. 2. Determine the force in members DC, DF, and CF. (15…

Q: C PROBLEM 10 25 12 Determine the tension in cable AC if the traffic light has a mass of 12 kg. A)…

Q: 13.] Thirteen spring balances are attached to the center ring of the force table. The following list…

A: For all the forces, consider below coordinate system, where positive x axis is along east and…

Q: 2kN/m D 4kN 4m 4m C 4m 4m 3m

Q: The given system of knotted cords (label the left knot as J and the right knot as K) supports the…

A: INTRODUCTION: We have a chord arrangement that is subjected to downward stress in this situation.…

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A: The free-body diagram of the hanging weight at point C is drawn below. Here, T represent the…

Q: Q/ Find the force just in members BD, CD and CE? 3 m 4m 3 m 3 m 3 m 3m 3 m 30 kN 30 kN 90 kN

Q: Examples Example (2) : Determine the tension in cables BA and BC necessary to support the 60-kg…

A: Given data :- mass of cylinder = 60 kg find the tension in each cable.

Q: Q3/ A 100 kg mass is supported by cables as shown in fig. below. Determine tension in each cables.…

A: Given, m = 100 kg

Q: Q/ Find the force just in members BD, CD and CE? B 3 m 4 m 3 m 3 m 3 m 3 m 3 m 30 kN 30 kN 90 kN

Q: Q1/ A 30 kg mass is supported by cables as shown in figure bellow. determine tension in each cables.…

A: When the system is in equilibrium under the action of three concurrent force, then their relation…

Q: Draw Free Body Diagram for two *pulleys W = 200 kN W = 400 kN 1m 2 m B 5.6 m

Q: Calculate the forces in members (a) DE; (b) BE; and (c) BC. Indicate tension or compression. 4 m D.…

Q: Q1/ A 30 kg mass is supported by cables as shown in figure bellow. determine tension in each cables.…

A: Given Data M=30 kg It is required to determine tension force in each cables

Q: Situation 2. To support the tent, the tension in the rope AB must be 35 lb. What are the tensions in…

Q: 30 1 Neglect the weight of the frame and compute the forces acting on all of its 20" members. 19 F…

Q: 3 m 5 m YF1 C. A weight is hanging on the structure. The weight exerts a force of F1 = (5.65x10^2)…

Q: ft. B `4 ft 8 ft 3 ft A Figure 03.12(a)

Q: A force P=95 lb causes the angle = 60° for equilibrium. Cord AB is 2 ft long. Take &= 50 lb/ft.…

A: To find: The unstretched length of the spring. Given: The stiffness of the spring is k=50 lbft. The…

Q: 11. Find the forces in all five cables. OD B. 60 30 kg

A: Given, m = 30 kg

Q: Two cables AB and CB are connected at the point where a force F is applied at an angle of = 20° If…

A: Given:θ=20°Tmax=500lb

Q: What is the maximum magnitude of the Force, F, that can be applied so the reaction force at A does…

Q: Determine the value of force P (in N).

A: To determine the value of Force

Q: An engineer trying to determine whether her crane will tip over when attempting to lift a 29K load.…

Q: 4. Five ropes in a pulley system support a large weight, w. What is the magnitude of the weight if…

A: In the Given pulley-block system Tension in rope1 = 100 N To determine The magnitude of weight…

Q: The 100 kg cylinder is suspended from the ceiling by cables attached at points B, C and D. Calculate…

A: ∑F=TAB+TAC+TAD-9.81=0rBA=(xB-xA)1 +0~(yB-yA)j^ + (zB-zA)k^ = (4i°+4j+zk^)m°r^BA= rBArBA=…

Q: 2. 4.19 Compute all reactions at the base A of the traffic light standard, given thatquno the…

Q: For P1=408 N and P2=859 N, the internal force in member AF is (assume all forces are tension) – 3…

A: Given: P1=408N & P2=859N

Q: 1. Compute the force in each member. 2000LB 3000LB B D 60 60° 60° 60 REH 10' 10'

Q: For P1=558 N and P2=698 N, the internal force in member DC is (assume all forces are tension) –3 m 3…

A: Given figure, In ΔCDE,

Q: Question # 2: Determine the force in each of the three cables needed to lift the ma that has a…

A: Givenweight of the macchine W=10kN

Q: QI: Determine the reactions of the support point for the truss as shown in Fig(1) ? 10KN 30m 3KN 30m…

Q: Q (4) Determine the force in cables AB and AC necessary to support the ( 12 kg ) traffic light shown…

A: Given: The mass of the traffic light is: m=12 kg The free-body diagram of the given situation is…

Q: PROBLEM 1 P1, P2 = 30 kips %3D Determine the internal force in the ff. members: [ Select] 1. DG (…

Q: (b) Find out the force and its nature of each member of the truss as shown in figure 2. |7 KN 24 KN…

Q: 2. Cable AB passes over the small ideal pulley C without a change in its tension. The length of…

A: Given data Weight of load W = 50N To determine the tension in the cable CD

Q: Three cables are used to support a 200 N load (Figure 2). Determine the tension in each 120 1207 2 m

Q: 3 m F1 5 m D. A weight is hanging on the structure. The weight exerts a force of F1 = (5.65x10^2) kN…

Q: Based on the diagram below, what is the force in Cable B so that the traffic signal is in static…

A: Given, W = 74 lb FA = 280 lb Consider below FBD:

Q: E2 ft+l ft IC |B D 100 lb/ft 3 ft 4 ft

A: A free body diagram is a diagrammatic representation of all the forces acting on the system…

Q: final Consider ACB as two segments (AC & CB) and 5ft each have a weight of 14 lb. If part DE is…

A: Giventwo segments AC and CBeach have a weight of w=14lb

Q: The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F…

Q: Determine the forces in membara CD and DF of the trues ahown in figure. 28 kN 18 kN D 4 m 4 m 4 m G…

Q: In figure (3), a spring of stiffness (K = 500 N/m) is placed against the 25 kg block. If the block…

Q: e cable forces acting on

Q: 2 m F F 3 m 5 m 5 m Q.2. Find the member forces at AB, AC, BC, BD and DC. Indicate they are in…

Q: Plot the tension in each cable as a function of d , if d varies from 0 to 8 m. The weight of the…

Q: What is the magnitude of the tension force at point D? 20° D A В 1.8 m 0.8 m → 0.4 m 25 kN

Question

Determine the force in each cable if F = 500 lb.
Ans:
FAC = 113 lb
FAB = 257 lb
FAD = 210 lb
%3D
1ft
6 ft
2 ft
3 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

If the input force to the compound lever is P = 30 lb, calculate the output force Q.
Determine the tensile force of the rope.
Draw the correct Free Body Diagram (FBD). Solve the tensile force developed in each cable necessary to support the streetlight, which has a weight of 3kN. Its height, y is 4m.
Determine the tensile force in all cables. The plate weighs 150 kg. (Answer: FB = 858 N, FC = 0 and FD = 858 N)
The platform scale consists of a combination of third and first class levers so that the load on one lever becomes the effort that moves the next lever. Through this arrangement, a small weight can balance a massive object. If a 3kg counterweight S is used to balance a 120kg load L, what is the value of 'x'? Draw all pertinent FBDs. Use g=9.806 m/s2.
Determine the tensions T1 and T2 in the strings required to maintain equilibrium for the suspended object weighs W = 38.7N shown in the figure. Take, α = 29.8° & β = 50.2°. The value of θ1 (Degree) = The value of θ2 (Degree) = The value of θ3 (Degree) =
F1 = 10 kN Determine the force in each member and state whether it is in tension or compression
the pipe AB is screwed in tightly to a pipe flange attached to the wall. It has two forces acting on it as shown below. Draw a complete FBD of the bar (its loads and support reactions). FB= (2i + 6j + 3k) kNFc= (1i - 2j + 2k) kN
Three cables are used to hold a w lb weight plate. Determine the tension needed on each cable to achieve the equilibrium position. givens->W: 713 Lb Y: 13 foot Θ°: 13°
A man holds a 35-kg ladder in his hands perpendicular to his hands (Figure 6). The free body diagram is shown on the right. If the maximum compressive force the person can withstand is 400N, determine:a) The minimum value of θ so that the person is able to hold the ladder.b) The compressive force at the end of the ladder at that time
What is the value of the tension in the rope in the case below? (g = 10 m / s2)
Given: F1=5 kN F2=12 kN F3=4 kN F4= 11 kN L=8 m Determine the force in member CF by the method of sections.