Determine the force in members FG, BF, and CE of the truss shown in the figure below. Let P = 29 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30° 60 60° 60° 60° 30 3P

Determine the force in members FG, BF, and CE of the truss shown in the figure below. Let P = 29 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30° 60 60° 60° 60° 30 3P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 01 The figure shows a truss which is pin connected at C and supported by a roller at D. It carries a vertical loads of 200 kN and 100 kN at joints A and E respectively. State if it is tensile or compressive. 4m D 2m A. E 200 kN 100 kN 6m 3m OCalculate the force in member DE. 2Calculate the force in member BE. 3 Calculate the force in member BC.
A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P end B as shown in figure. The wire is made of high- strength steel having modulus of elasticity E= 210 GPa. The diameter of the wire is 5mm. Determine the maximum load P that could be applied so that the vetical displacemt at B will not be more than 6 mm?
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A frame and loading are shown. B P 2 120 mm 120 mm D of c 120 mm 90 mm ↓ Determine the force acting on member ABC at C. Take P= 320 N. The force acting on member ABC at C is N.
The force in member AB of truss joint B shown in figure is given as 15 N B• - 10 N AB a. 10 N compression b. 10 N tension c. 15 N compression O d. 15 N tension
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 512 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 643 mm2. For the 32 kN force shown, determine the deflection of D (mm) *Note: Negative if compression and positive if tension. Also, the final answer should have two decimal places.
TEXT:A planar construction is composed of two beam elements and two axial rods. These arejoined with frictionless joints, as indicated on the sketch. The structure is applied an outer concentrated load P=8kN in node G and a downwardevenly distributed load q=4kN/m between junctions A and D. The beam ABCD and EFG are torque rigid,while the axial rods BF and CF only absorb forces in the direction of the rods. A) Calculate the rod forces and for the external given load effect.B) Calculate the bearing reactions for the external given load effect.
Below is a truss created with 3 rod elements. Fixed at point A, sliding support at point Chas. At point B, the load P acts on the system as shown. All 3 elements have the same cross-section and are rectangular.section dimensions are given in the figure. If the safety factor used in the design is 2.5, the buckling stability should be taken into account.Calculate the highest value of the load P. E = 20 GPa
Calculate force in DE and DF
Given the figure below determine the bar force at AB and BD
A For the beam loaded as shown in figure, the location of point of contra flexure from the left end is L Wo B
The wooden strut is subjected to the loading shown. Draw the state of stress at point C on an infinite small element. The strut is supported by a bolt (pin) at point B and a roller support at point A. 50N S0N 40N 40 N -60 100 mm 50 mm 25 mm 200 mm 200 mm'200 mm'200 mm 100 mm 100 mm
Page I of 2 PROBLEM 2 A steel bar is bolted to another solid steel structure as shown in Figure 2. A force 400 N, which is on the plane ABCD, is acted at E. Plane ABCD is bent vertically downward at AB by 30°. Given P= 448 mm. Show 3-D Cartesian x-, y- and z- axes at point E or F. Express the force 400 N in Cartesian vector. [Ans; F = {100v6i + 200v2j – 100vZk} N or {244.949i + 282.843j-141.421k} N] Determine the moment caused by the force 400 N about (i) point F, (ii) M-N axis, and (iii) F-B axis, if AB = CD = 75mm. Express your answer in N'm. [Ans: (i) Position vector = FE = {(448+75V3)i + 150j 175k} mm; MF {28.3i + 38.9j + 127k} Nm; (ii) MN is parallel to y-axis, MMN= 38.9 Nm; (iii) uFB = 0.9035i + 0.3781j - 0.2017k; MFB = 14.7 Nm] 2a) 2b) %3D 2c) M 100 mm 150 mm 30° B P (mm) D 150 mm 45° 400 N Figure 2