TAKORADI POLYTECHNICSCHOOL OF ENGINEERINGEND OF FIRST SEMESTER EXAMINATIONS (2015/16)HND MECHANICAL ENGINEERING II [PLANT & PROD] [REGULAR]COURSE: MECHANICS OF MACHINES IICOURSE CODE: MCE 233JANUARY, 2016TIME: 3HOURSINSTRUCTION: Answer all four (4) questionsQUESTION 1State two conditions for which a system is describe to be performing asimple harmonics motioni)In a simple crank and connecting rod mechanism, the connecting rodand the crank are 350mm and 50mm long respectively when the crank isii)300 from thedead center position, find the velocity and theacceleration of the piston at 10rev/s. assume the motion of the piston tobe simple Harmonic motion. What is the maximum velocity andacceleration of the piston.QUESTION 2Determine the frequency of a spring loaded system shown below given thatm = 3kg, k, = 3N/m. k2 = 0.06KN/m , k3 = 1.1N/m, k, = 0.4KN/m, kg = 67N/m李 K4E K2KSK3

Answered: Image /qna-images/answer/15dd690a-4f32-484d-b621-1954b0383b76.jpg

Answered: Determine the frequency of a spring…

Determine the frequency of a spring loaded system shown below given that m = 3kg, k, = 3N/m. k2 = 0.06KN/m , k3 = 1.1N/m, k4 = 0.4KN/m, ks = 67N/m %3D %3D %3D %3D EKS

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Help me with this ASAP. Thank you! Find the Following: 1. Natural angular velocity 2.Damped angular velocity 3. Equation of motion x(t). Assume Initial conditions for displacement and velocity 4. Graph 2 cycles of the vibrating system. You can use third party app for this.
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
Answer all questions below showing revelent calculations and working with explanation where necessary. 1.Create a mathematical model for the system shown. 2.Develop a transfer function for 0(s)/Qi(s), state the constants that you have used in your transfer function. [Hint: You would also need to derive Q(s)/Qi(s) to predict a theoretical value for the increase in rotational speed ] [Note: Omega, Q=Angular speed] 3. With the use of theoretical values, determine the theoretical increase in rotational speed expected for the water wheel when the inflow is increased by a step. This should be repeated for three different step input values. Show calculations and working throughout.
Context The needle of a sewing machine makes a repetitive up and down motion which is described by the equation y(t)=Acos(wt) To choose the settings of the device that will ensure that the needle successfully pierces the textile, you are asked to model the speed in ? of the needle as a function of time. Constraints and information The parameter A represents the range of motion (in m);The parameter w represents the angular frequency. It tells us about the number of back and forth movements that the needle makes per second;The parameter w is given in rad/s, so your calculator absolutely must be in radians mode to do the calculations in this problem;Modelization Establish the model for the y velocity of the needle as a function of time and the parameters A and w. Then test your model by calculating the speed in y of the needle at the moment and with the given parameters: Moment: 4.1 s Amplitude: 0.012 m Angular frequency: 17.9 rad/s
Please help me doing part B all I need help with is too make the derivation of equations of motion, and derivation of the state equations, and that will do for part B if you could help me with this it would make my life alot easier, and no matlab is not necessary for this.
Topic mechanics of machines, chapter harmonic motion for diploma level.pls give step by step solution.dont type ,write clearly.appreciate your help.
2.A 31 kg skip attached to a steel rope on a crane is used to hoist bricks from the ground to the top of a construction site. The steel rope is wound onto a lifting drum with a diameter of 700 mm and rotational frequency of 52 revolutions per minute. The lifting drum is situated on the top floor which is 196 m high. How many seconds will it take to lift bricks, three quarters up the height of the building?
Power Engineering - ABEN 3411 Illustrate and discuss the principle of operation for diesel and gasoline engine.
You and a friend are raising a beam, but your friend's rope is too short so you lift him off the ground. At the current time, everything is static. The tension in your cord is 1045.6 N, the mass of the beam is 15 kg, and the mass of your friend is 85 kg. The length of the beam is 4.9 m, d = 3.9 m, theta = 43.5 degrees, phi = 62.5 degrees. If you choose the base of the beam as the origin, and the positive torque direction as counter-clockwise, what is the torque from your cord on the friend+beam system?
Can you please answer quickly What is the purpose of the problem called kinematic problem in robotics? Finding the position of the robot's joint variables when the robot's end function is posedFinding the position of the robot end function when the joint values of the robot are givenFinding the rate of change of the robot end functionalist's pose given the speed of the robot's joint variablesFinding the speed of the robot's joint variables when the speed of change of the robot's end function's pose is given
What is an element by element operation in matlab?
The schematic diagram of a large cannon is shown in Fig. 2.31. When the gun is fired, high pressure gases accelerate the projectile inside the barrel to a very high velocity. The reaction force pushes the gun barrel in the direction opposite that of the projectile. Since it is desirable to bring the gun barrel to rest in the shortest time without oscillation, it is made to translate backward against a critically damped spring-damper system called the recoil mechanism. In a particular case, the gun barrel and the recoil mechanism have a mass of 500 kg with a recoil spring of stiffness 10,000 N/m. The gun recoils 0.4 m upon firing. Find (1) the critical damping coefficient of the damper, (2) the initial recoil velocity of the gun, and (3) the time taken by the gun to return to a position 0.1 m from its initial position.