Determine the magnitude of the resultant force of the water acting on the circular glass plate that is bolted to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top.

Determine the magnitude of the resultant force of the water acting on the circular glass plate that is bolted to the side panel of the tank. Also, determine the location of the center of pressure along this inclined side, measured from the top.

Name: F2-11. Determine the magnitude of the resultant force ofthe water act
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: F2-11. Determine the magnitude of the resultant force ofthe water acting on the circular glass plate that is boltedto the side panel of the tank. Also, determine the locationof the center of pressure along this inclined side, measuredfrom the top.3

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
The trough is filled to its top with carbon tetrachloride. Determine the magnitude of the resultant force acting on the semi-circular end plate, and the location of the center of pressure from the top.
Determine the magnitude of the force acting on a 2 m diameter gate which is inclined 60° from the vertical if the height of oil above the bottom of the gate is 3 m (SG of oil = 0.87).
Determine the resultant force USING GENERAL SOLUTION of the oil exerts on the semicircular surface AB.The tank has a width of 3 m. Take liquid density as 900 kg/m3.*USE GENERAL SOLUTION AND SHOW PRESSURE DIAGRAM
A swimming pool has a width of 4 m and a side profile as shown. Determine the resultant force.Determine the magnitude that the water exerts on walls AB and DC, and on the bottom BC, using the general solution. Determine also its direction and location.DRAW PRESSURE DIAGRAM
The initial pressures at A and B are the same at 103 kPa. If the pressure at the liquid at A (SG1 = 1.25) is increased to 148 kPa while keeping the pressure at B constant, determine the new position (Δh, in mm.) of the mercury meniscus inside the tube as shown. Assume no change in the liquid densities. The connecting tube is a 1-cm in diameter, Y1 = 0.51 cm, and the inclination of the tube is 18 degrees with respect to the horizontal. Assume unit weight of air to be negligible.
The tank is fined with water. Determine the resultant force acting on the triangular plate A and the location of the center of pressure. Measured from the top of the tank. Solve the problem using the formula method
The volume of the fluid inside the upright conical tank is 0.8 ft3. (a) Determine the needed volume to fill up the entire container. (b) Determine the height of the air from the peak and base of the tank. (c) If the mass of the fluid is 40 kg, determine its density.
Det the magnitude and location of the equivalent hydrostatic force acting on the circular gate if the water level is maintained as shown
A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 5 kg and a cross-sectional area of 35 cm2. A compressed spring above the piston exerts a force of 75 N on the piston. If the atmospheric pressure is 95 kPa, determine the pressure inside the cylinde
Determine the magnitude and location of the resultant force acting onthe triangular end plates of the water trough shown; ρw = 1000 kg/m3.
Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. Strictly using General Solution, and please show pressure diagram.