plassss answerrr sdasdw Determine the magnitudes of all pin reactions for the frame loaded as shown.Part 1765mmT35°Answer: BD-The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the force BD.Ay330mmi64°710 Nby640NBD710 N

Answered: Image /qna-images/answer/f319e9da-009c-48a7-b321-98594b0cd82a.jpg

Determine the magnitudes of all pin reactions for the frame loaded as shown. Part 1 765 mm Ax 35⁰ Answer: BD- 330 mm Ay 64° The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the force BD. 710 N D 640 N BD 710 N C

Determine the magnitudes of all pin reactions for the frame loaded as shown. Part 1 765 mm Ax 35⁰ Answer: BD- 330 mm Ay 64° The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the force BD. 710 N D 640 N BD 710 N C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.63P: For Probs. 4.61â€“4.68, (a) draw the free-body diagrams for the entire assembly (or structure) and...

See similar textbooks

Related questions

Q: A fuel oil of 20⁰API at a temperature of 15.6⁰C has a heating value of 44, 240 kJ/kg. Determine the…

A: Solution: Given Data: The API of fuel is, 20oAPI The temperature of the fuel is, T=15.6oC The…

Q: The turning moment diagram for a petrol engine is drawn to the following scales: turning moment 1 mm…

A: The fluctuation of energy corresponds to 600 mm2. The density of the flywheel is 7200 kg/m3. The…

Q: Air at 25°C flows over a 9-mm-diameter sphere with a velocity of 30 m/s, while the surface of the…

Q: Cages used for supporting bearings in an aero engine have been tested under simulated operating…

A: L10 = 2730 hours. (The maximum hours) For 90% reliability Total number of tests = 64 Samples…

Q: A simple carburetor is adjusted for a 15.2:1 air-fuel ratio at sea level and 600F. Determine the…

A: Solution; Given Data: The air-fuel ratio is, A/F=15.2:1 The temperature of the fuel is, T=60oF The…

Q: 1. (i) Refer to the planes shown below (labeled (i), (ii), (iii) and (iv)) and choose which of the…

A: Given:

Q: Electrical strain gauges were applied to a notched specimen to determine the stresses in the notch.…

A: Given:Strain along the x-axis, εx=0.0019Strain along the y-axis, εy=-0.00072

Q: The horizontal bar shown is pinned at O and is supported with a helical spring at L1 from O. L1=2m,…

Q: Question 3: a) In a '72.77' mm diameter pipeline conveying air, the inlet Mach number is measured to…

A: Given: M = 0.5198 Average friction factor f = 0.02 Length = 1 To find : Sonic length Mach number at…

Q: 6-1 Determine the flow rate through the Venturi meter shown in the diagram if the ideal conditions…

Q: Disk A impacts disk B, which is initially at rest, as shown in the figure. If the coefficient of…

Q: An amount of 0.75kg of gas is contained in a tank, the volume of which is 2ft3 . If the internal…

Q: for the power wouldn't it be desnity x Q x hp / 0.75 ? or did my professor make a mistake

Q: 7-10. A simple carburetor is adjusted for a 15.2:1 air-fuel ratio at sea level and 600F. Determine…

A: Given DataAFRs(sea-level)= 15.2:1Temperature at sea level (Ts) = 60oF…

Q: f the following, the SHORTEST is ________. a. 1.5-mile b. 1610 m c. 6335 inches d. 17600 yards

A: Given:To determine the shortest among the given options.

Q: *3/104 In executing the biceps-curl exercise, the man holds his shoulder and upper arm stationary…

A: The force is balanced by resolving the components of Tb The moment about point D is zero as the…

Q: 23. Consider that 1 lb of air has a decrease of internal energy of 20.58 Btu while its Fahrenheit…

A: Given:mass of the air, m=1 lbdecrease of internal energy, ∆u=-20.58 BTUfinal temperature, T2=T13

Q: If 10 kg/min of air are compressed isothermally from p1 = 96 kpa and V1 = 7.65 m3/min to p2 = 620…

Q: An amount of 0.75kg of gas is contained in a tank, the volume of which is 2ft³. If the internal…

A: Given data:- mass of gas = 0.75 kg the volume of which =2ft3 the internal energy decreases =30kJ…

Q: 2. For the non-concurrent forces shown, solve for the moment at point D. 1' 1591b 1301b 2501b D…

Q: Question 4: 1. Assign three jobs on three machines for following cost matrix job J1 A 12 B 13 C M1…

A: Given:

Q: A) Assuming that no inputs are present to a first-order and a second-order systems, mention two…

A: Solution: Given Data:

Q: Nitrogen is cooled at a constant pressure of 1200 P final specific volume of 0.75 m³/kg. If the mass…

A: GivenP=1200PaV1=1.80 m3/kgV2=0.75 m3/kgCp=1.0399 kJ/kgKk=1.399m=2.26kg

Q: Determine the moment of inertia of the shaded area about the x-axis (a = 9 mm.)

A: Given: Determine the moment of inertia of the shaded area about the x-axis (a = 9 mm.)

Q: Determine the force in member CG. The force is positive if in tension, negative if in compression.…

A: The given data in the problem is represented in the following attached image:

Q: Find solutions for the divergence and curl of the vector field y at (1, 0, -1). v (x, y, z) = x²z²į…

A: The vector field is V=x2z2i⇀+xyzj⇀+zcosy4k⇀. The position is (1,0,-1) The divergence is ∇·V is the…

Q: The following gravimetric analysis on an ash and moisture free basis of a kilogram of Fuel oil are…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

Q: A four bar mechanism PQRS with link PS fixed. The length of the links are PQ=4cm, QR=9cm, RS=5.5 cm…

A: Given: A four bar mechanism PQRS with link PS fixed. The length of the links are PQ=4cm, QR=9cm,…

Q: Answer with true (T) or false (F), corrects the wrong statements, and give short reasons for…

A: As per the guidelines, we have to solve 3 questions at a time. Given Data: The following statements…

Q: A spool with radius R = 3 ft is released from rest on an incline with 8 = 30°, and its center, which…

Q: 2 Show the Moment of Inertia About an Arbitrary Axis IÃa = Ixxu} + Iyyu} + IzzU² − 21xyUxUy −…

A: Given: To find: Moment of inertia about an arbitrary axis

Q: From previous Figure 1, fill in the table given. (No need to show calculation step) (Hint: Output…

A: The output torque is To. The output speed of pulley is N=150 rpm. The diameter of the shaft is given…

Q: Four bar mechanism PQRS with link PS fixed. The length of the links are PQ = 4cm, QR = 9cm, RS =…

A: Given: Four bar mechanism PQRS with link PS fixed. The length of the links are PQ = 4cm, QR = 9cm,…

Q: Prob # 8. If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0…

A: GivenI=80 lb-ft2N=0 t o N=1500 rpm in t=3sTstarting=10 lb-in=1012 lb ft=1012×32.17 lb ft2/s2=26.808…

Q: Prob # 9. Find the horsepower transmitted by a pair of friction wheels, the diameter of driving…

Q: The paint stirrer shown in the figure is made from a rod of length 76 and mass p per unit length.…

Q: A flashed-steam geothermal power plant is located where underground hot water is available as…

Q: The manufacturer of a product that is subjected to repetitive cycles has specified that the product…

A: Solution: Given Data: The length of the crack is, a=0.02 mm. The fracture toughness of the material…

Q: Question/ Do a small research about the types of condensers in powerplant.

Q: The upper and lower edges of a circular gate of length 4 m are at depths of 1 m in water. What will…

A: Given circular gate as shown below

Q: →Compare (100) and (111) surfaces in FCC. Which one should have a lower surface energy?

A: To compare: The (100) and (111) surfaces. Concept used: (100) surface: The fcc metal is cut parallel…

Q: The specific gravity of the manometer fluid shown in the diagram is 1.07. Determine the volume…

Q: The ball of mass q has a velocity of 2.5 m/s which is directed tangent to its curved path. At the…

Q: ollowing integrand is the product of an odd and an even function. What is the result of the integral…

A: Given integration is

Q: If r = (x, y, z), prove that v ( ² ) = - = /1 r

A: To prove: The ∇1r=-r→r3. Given: The given vector is r→=xi^+yj^+zk^.

Q: "For section 7, list the ONE PRIMARY way that heat transfers through this section. Section 7…

Q: A four bar mechanism PQRS with link PS fixed. The length of the links are PQ=4cm, QR=9cm, RS=5.5 cm…

A: A four-bar mechanism PQRS with link PS fixed. The crank PQ rotates at 10 rad/s clockwise.

Q: A+ Section Section Pump efficiency (np) = 80% Diameter (D)= Golm Calculate the power Pomp for a pump…

A: The diameter of section 1 is d1=0.1 m. The diameter of section 2 is d2=0.065 m. The velocity in…

Concept explainers

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.

Question

plassss answerrr sdasdw

Determine the magnitudes of all pin reactions for the frame loaded as shown.
Part 1
765
mm
T
35°
Answer: BD-
The Free-Body diagram for bar ABC is shown. Note that bar BD is a two-force member. Solve for the force BD.
Ay
330
mm
i
64°
710 N
by
640
N
BD
710 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the forces in members a) AB, b) AG, c) GF, d) BF, e) BC. PLS USE JOINT METHOD GIVEN: W1= 13 kips W2= 12 kips b°= 39 degree a°= 7 degree L1= 3 ft L2= 8 ft L3= 7 ft PLS SHOW COMPLETE SOLUTION, WRITE LEGIBLY AND ONLY ROUND OFF THE FINAL ANSWER IN FOUR DECIMAL PLACES, ANSWERS SHOULD BE IN THE ATTACH TABLE. PLS SHOW THE FREE BODY DIAGRAM ON EACH JOINTS AND IN THE ANSWER IDENTIFY IF IT IS A TENSION OR COMPRESSION. PLS USE THE GIVEN VALUES I ALREADY KNOW THE A B AND C PLS SOLVE NOW D AND E AND THE ANSWER SHOULD BE IN THE ATTACHED TABLE
Determine the forces in members a) AB, b) AG, c) GF, d) BF, e) BC. PLS USE JOINT METHOD GIVEN: W1= 13 kips W2= 12 kips b°= 39 degree a°= 7 degree L1= 3 ft L2= 8 ft L3= 7 ft PLS SHOW COMPLETE SOLUTION, WRITE LEGIBLY AND ONLY ROUND OFF THE FINAL ANSWER IN FOUR DECIMAL PLACES, ANSWERS SHOULD BE IN THE ATTACH TABLE. PLS SHOW THE FREE BODY DIAGRAM ON EACH JOINTS AND IN THE ANSWER IDENTIFY IF IT IS A TENSION OR COMPRESSION. PLS USE THE GIVEN VALUES VALUES OF LETTER D AND LETTER E SHOULD BE IN THE ATTACHED TABLE PLS
determine the magnitude of the vertical reaction force at pin D also. only HANDWRITTEN answer needed ( NOT TYPED)
a 50 KG TRUCK ENGINE IS LIFTED USING THE SETUP SHWON BELOW. aSSUMING THAT THE PULLEYS SHOWN IN THE DIAGRAM ARE FRICTIONLESS, WHAT FORCE (p) MUST BE APLIED TO THE CABLE TO HOLD THE ENGINE IN THE POSITION SHOWN BELOW WITH d = 1mm? (Hint drawl free body diagram of pullys supporting the engine block) please show all work thank you!
Given the Frictionless Frame as shown below with pin connection atPoint A and Point C.Determine the following if the uniform load is ‘w’:a.) The Internal Reaction at Point A in terms of w.b.) The External Reaction at Point B in terms of w.c.) The Internal Reaction at Point C in terms of w.d.) The External Reaction at Point D in terms of w. NOTE: 3 DECIMAL PLACES
Solve the effective normal force on the rod CD Use units [N,mm] The mass of the load is: mk=21904 kg
Referring to Prob. 10.43 and using the value found for the force exerted by the hydraulic cylinder CD , determine the change in the length of CD required to raise the 10-kN load by 15 mm.Reference to Problem 10.43:
Method of joints: The truss pinned to the floor at D, and supported by a roller at point A is loaded as shown in Fig. T-06. Determine the force in member CG. (with explanation)
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions please don't skip. Thanks!
Use the method of joints to find the force in members HP and TU. Indicate whether the forces are in tension or in compression.
The automobile bumper jack is designed to support a 4000-N downward load. Begin with a free-body diagram of BCD and determine the force supported by roller C. Note that roller B does not contact the vertical column
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions don't skip. Note that the sums for Fx and Fy should be zero.