Determine the material property of the materials from the following website. Material Property Data (www.matweb.com) Material: Carbon Steel C1045 (AISI 1045) Hot Rolled - 1 in. round Property: Ultimate Tensile Strength (psi) 81900

Q: A foreman is exposed to the hand tool vibration for 30 + R minutes with the vibration values of ax =...

A:

Q: Two identical upright cylindrical tanks contains H2O, the first tank is full and the second is 2/3-f...

A:   leth−height of both tanksso water level in first tank is h and in seocnd tank is23hLet area of sur...

Q: Explain the typical Printed Circuit Board (PCB) manufacturing process.

A:

Q: Determine pressure due to water at depth of 20 m on a body

A: Given data,  H= 20 m  Fluid is water

Q: he tensile curve of a material is given. a) Mark the strength points of the material on the curve. b...

A: Given: The tensile curve of a material

Q: C. From the given coplanar force system which consists of two forces and one couple. Replace the for...

A:

Q: A foreman is exposed to the hand tool vibration for 31 minutes with the vibration values of ax = 44 ...

A: We will solve the question by using the 'ready reckoner' table, For the vibration of 44 m/s2 and exp...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

A:

Q: What diameter of new cast-iron pipe, 1 mile long is required to discharge 4.5 cu. ft. per second und...

A: L=1 mile Q=4.5 ft3/secH=50 ftg=32.2 ft/sec2Now since Q=π4×D2×VAnd V=2gH

Q: The internal drag truss for the wing of a light airplane is subjected to the forces shown. Determine...

A:

Q: 2. What did Altshuller use as a basis for the systematic procedures he developed in TRIZ? 3. Can TRI...

A: TRIZ is a russian abbreviation and its english stands as Theory of Inventive Problem Solving. It is ...

Q: A wooden ball is tied to a string of length 65 cm and rotating in horizontal circle at a constant sp...

A:

Q: se two metals due to their crystal structures.

A: Differences between Gold( Au) and Chromium( Cr) metals, Based on their Structure.

Q: Top. Polyamide polymer that has a relatively low glass transition temperature and resists chipping. ...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: 2 m-1)° = y + 0.6 m = 1 m 10 S

A: Calculated velocity gradients and shear stress.

Q: The following table presents the highway gasoline mileage performance and engine displacement for Au...

A: a.The simple linear model fit for given data is: Hence the regression line is given by:  y = 39.155...

Q: 25: Determine the resultant of the system shown, and locate it with respect to point Co) 20N 40N 5 c...

A:

Q: Find the power transmitted by a belt running over a pulley of 600 mm diameter at 200 r.p.m. The coef...

A: N=200rpm T1=2500N D=600mm  

Q: Write any two differences between NC & CNC and four advances of CNC.

A: The difference between NC and CNC, NC stands for numerical control and CNC stands for computer numer...

Q: onnected by re of pin E ne periphery

A:

Q: A ski is made up of: 1. Top. Polyamide polymer that has a relatively low glass transition temperatur...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: A mixture of dry air and water vapor is at a temperature of 21 C under a barometric pressure of 101....

A: Since we only answer up to 3 subparts so we will answer only up to 3. Please resubmit the question b...

Q: A 4-stroke, 4-cylinder Spark Ignition engine is running at a speed of 1800rpm following an air stand...

A: Number of cylinder k=4 ,4 stroke N=1800 rpm V1=VT=750 cm3 ,Vc=90 cm3Compression ration r=75090=8.33 ...

Q: A box that contains of a 250 kg fragile instrument is transported by a truck that is subjected to a ...

A:

Q: Determine the Sound Pressure Level, SPL at 20 + T meters from a speaker in a reverberant room if the...

A: Find sound pressure level (L1) R1=29m R2=7m L2=100dB

Q: Explain the processes of Rankine cycle with a neat TS diagram.

A: Given Data  Explain the processes of Rankine cycle with a neat TS diagram.

Q: Aroomiscooledbycirculatingchilledwaterthroughaheatexchangerlocatedin a room. The air is circulated t...

A: Given data as per question shaft output =0.25 hp Efficiency =54%

Q: Try One scene 13 of 13 Bar properties 800 mm Determine the internal forces and normal 500 mm? stress...

A:

Q: In a cogeneration cycle, the water vapor in the turbine expands from 6000 kPa and 440 °C to 8 KPa. T...

A:

Q: 1) Prof. K. climbed a wall and is now stuck and hungry. One of her ME 242 students saw this opportun...

A:

Q: A single-acting, two-stage air compressor with perfect intercooling delivers 15 kg/min of air at 25 ...

A: Given data: P1 = 1 barT1 = 15°C = 288Kn=1.25Q = 15 kg/min = 0.25 kg/sP3 = 25 barDensity of air at 15...

Q: (a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b) De...

A:

Q: A tennis ball is projected upward with a velocity of 120 m/s. Neglecting air resistance, how long wi...

A: Correct answer: (c) 25s

Q: Illustrate and discuss the two ways of throttling using one-way flow control valves

A:

Q: Given: diameter of pipe in point 1 = 3.9in diameter of pipe in point 2 = 2.5in specific gravity of ...

A: Given data, Diameter of the pipe at point 1, d1 = 3.9 in Diameter of the pipe at point 2, d2 = 2.5 i...

Q: are such. nd thei- nei: ular to

A:

Q: A steam power plant running on Rankine cycle has steam entering HP turbine at 20 MPa, 500°C and leav...

A: We draw the Temperature(T)-Entropy(S) curve for the rankine cycle, Using steam table we find enthal...

Q: The pitch (angular motion) and bounce (up-down linear motion) of a motor vehicle is shown in Figure ...

A: When an object is disturbed, its natural frequency is the frequency or rate at which it vibrates. Th...

Q: An oil of viscosity 0.8 Pa-s and specific gravity 1.2 flows through a horizontal pipe of 80 mm diame...

A:

Q: 5. An angle bracket ABC is restrained by a high- strength steel wire CD, and it supports a load P at...

A:

Q: A 2D velocity field is given by V = (u, v) = (2.8 - 1.6x, 0.7 + 1.6y), where the coordinates are in ...

A: Answer: The magnitude of vorticity is 0.  

Q: What is the velocity of a ball 5 sec. after it is dropped from rest from the top of the Sears Tower ...

A: Given data,  ball is dropped from top of tower,  So Initial velocity is u=0 m/s  Need to find veloci...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

A:

Q: For a given Rankine Cycle, the difference between the heat added and the heat rejected is not equal ...

A: Net work: The difference between the work produced by the turbine and the work input to the pump is ...

Q: y 960 mm? AT = -25°C 80 GPa 165 kN 15.7 x10-6/°C (1) 1920 mm? (2) A %3D B E2 160 GPa %3D 19.7 x106/°...

A: Find the force in each bar and stress in each bar and deflection of point B Given data:- A1=960mm^2 ...

Q: A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40C and...

A:

Q: Q.2) A car of mass 1200 kg is standing on a 20° incline with the horizontal. What are the components...

A: Hi. as you have posted multiple questions and have not specified which question needs to be solved, ...

Q: force of F = 50 N acting on a ring is shown in Figure 2.3. Express the force as a artesian vector.

A:

Q: A foreman is exposed to the hand tool vibration for 30 minutes with the vibration values of ax = 6/s...

A: (i) Write the given data. ax=6 m/s2ay=7 m/s2az=4 m/s2t=30 min

Q: A 50 kN block is resting on a horizontal plane with a coefficient of statics friction of 0.3. Determ...

A: The necessary information given in the question is written below as- The static friction coefficient...

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.