Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 = 2KN     F1 = 9KN

Q: The bar has a 60 mm by 15 mm rectangular cross section. If P = 50 kN, determine the normal stress…

A:

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A:

Q: If the allowable normal stress for the bar is s allow = 120 MPa, determine the maximum axial force P…

A: Write the given data:

Q: The two steel members are joined together using a 30° scarf weld. Determine the average normal and…

A: Separating both the portions of the steel members and showing the forces on the plane a-a

Q: Determine the state of stress at point A on the cross section of the shaft at section a–a. Show the…

A: The free-body diagram of point A is written as, On using the force equilibrium in the z-direction,…

Q: Determine the maximum normal stress that loading produces in the steel member.

A:

Q: Determine the state of stress at point A on the cross section at section a–a of the cantilever beam.…

A: The moment at section a-a is given as, From the bending equation, The bending stress at point A…

Q: The bronze C86100 pipe has an outer diameter of 1.5 in. and a thickness of 0.125 in. The coupling on…

A: Given data as per question Outer diameter of pipe = 1.5 in Thickness = 0.125 Force ,F = 20 lb

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: The frame supports the distributed load shown. Determine the state of stress acting at point D. Show…

A: In this problem, the state of stress at point D is determined by drawing the FBD as discussed in the…

Q: Qi: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress…

A:

Q: The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a…

A:

Q: F8-3. Determine the state of stress at point A on the cross section of the beam at section a-a. Show…

A:

Q: The column is subjected to an axial force of 8 kN which is applied through the centroid of the…

A:

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w)    = 10 lb-ft the FBD of the cut segment of the rod is…

Q: Determine the stress in member CE assuming that the area in steel is 24 mm^2 p= 5 kN 3m 2m 2m 2m

A:

Q: The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal…

A:

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: 1: Stress in the left rod after its lower end is attached to the st

A:

Q: Which stress element below correctly shows the normal and stress at point 2 which located at the top…

A: Given

Q: Determine the maximum axial force P that can be applied to the bar. The bar is made from steel and…

A: The given bar is critical to two positions:1) At the fillet section2) At the hole sectionAt fillet…

Q: Determine the maximum normal stress (in MPa) developed in the bar when it is subjected to a tension…

A:

Q: A 100kg lamp is supported by two rods AB and BC. If AB has a diameter of 10mm and BC has a diameter…

A:

Q: The 6061-T6 aluminum bar has a square cross section of 25 mm by 25 mm. If it is 2 m long, determine…

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: Given:- P=2kip,Width of section of bar with hole,w1=1.875 inch,Width of section of bar without…

Q: The rod has a diameter of 1 in. and a weight of 15 lb>ft. Determine the maximum torsional stress…

A: Given: The diameter of rod is D = 1 in. The weight of the rod is M = 15 lb/ft. The length of the…

Q: The grains of wood in the board make an angle of 20° with the horizontal as shown. Determine the…

A: Given, Load P = 250 N Load Perpendicular to AB' = Pn N Load Parallel to AB' = Ps N Length L = 300 mm…

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: F1-11. Determine the average normal stress developed at points A, B, and C. The diameter of each…

A:

Q: Question: Determine the average shear stress in the single pin A and double pin B as well as the…

A: The UDL can be converted to point load by taking the area of the applied load surface and point it…

Q: The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the…

A: Given data: The allowable bearing stress of the washers on the boards, (σb)allow = 2 ksi. The…

Q: | Determine the stress components acting on the inclined plane AB. Solve the problem using the…

A: We have to solve the equilibrium methods

Q: The member is to be made from a steel plate that is 0.25 in. thick. If a 1-in. the hole is drilled…

A: Calculate the approximate width w of the plate…

Q: F9-7. Use Mohr's circle to determine the normal stress and shear stress acting on the inclined plane…

A:

Q: Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 2…

A: At fillet rh=0.251.25=0.2wh=1.8751.25=1.5   From the table  The stress concentration factor,  K=1.73

Q: An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20…

A:

Q: The L2 steel blade of the band saw wraps around the pulley having a radius of 12 in. Determine the…

A: Given data: The radius of curvature of the pulley, ρ = 12 in. Width of the blade, w = 0.75 in. The…

Q: The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress…

A:

Q: Determine the state of stress at point A on the cross section of the pipe assembly at section a-a.…

A:

Q: The elbow of the pipe has an outer radius of 0.75 in. and an inner radius of 0.63 in. If the…

A: Given, M= 25 lb.in

Q: Q1/ The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial…

A: TO DETERMINE: The average stress as the function of x. GIVEN: area A Load wo length 2a DIAGRAM:

Q: A 2" diameter pin connects the three links as shown. The links have a 3" by 3" cross- section.…

A: Given data: The diameter of the pin is d = 2 in.. The cross-section of the link is 3 in.×3 in.. The…

Q: The two members used in the construction of an aircraft fuselage are joined together using a 30°…

A:

Q: The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in.…

A: Write the given data with suitable variables. LCu=12 indCu=1.25 inLAl=6 indAl=1.25 inαAl=13×10-6…

Q: Determine the maximum normal stress that loading produces in the 6061-T6 aluminum plate. 0.25 in.…

A: