Determine the minimum flow capacity Qfilter, in units of liter per minute (Ipm), of the return line filter shown. The pump flow rate is Qpump = 30 lpm (liter per minute) and the cylinder piston and rod diameters are 80 mm and 40 mm, respectively. [Hint: 1 liter = 1 dm³ = 0.001 m³, Qfilter = (Apx Qpump)/(Ap-AR) where Ap and AR are the cross-sectional area of the piston and rod, respectively] # RETURN LINE Figure: Full flow filter in return line O 30 LPM O 38.1 LPM 44.2 LPM O 40 LPM O 1.33 LPM

Determine the minimum flow capacity Qfilter, in units of liter per minute (Ipm), of the return line filter shown. The pump flow rate is Qpump = 30 lpm (liter per minute) and the cylinder piston and rod diameters are 80 mm and 40 mm, respectively. [Hint: 1 liter = 1 dm³ = 0.001 m³, Qfilter = (Apx Qpump)/(Ap-AR) where Ap and AR are the cross-sectional area of the piston and rod, respectively] # RETURN LINE Figure: Full flow filter in return line O 30 LPM O 38.1 LPM 44.2 LPM O 40 LPM O 1.33 LPM

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
The water flow of 35,000 Liters/min was developed into a booster station with a pump installed rated as follows: Pressure at Discharge side= 4.18 bars, 850mm above the pump C.L Suction Pressure= 220mmHg vacuum , 425mm below the pump C.L Pipe Dia @ suction=16 inches and Pipe Dia @ Discharge 12 ½ inches. 1. Draw the illustrative diagram 2. Calculate the Head at discharge, Velocity Head, Elevation Head and the Total Head of the Pump.
Given:Q = 28 lit/sKc = 0.40Kb = 0.5Ke = 0.40Pipe diam = 10 cmFriction factor = 0.037 1.) From the given data of Figure 1: a) Calculate the value of H. b) If a straight pipe is used from A to B, determine the new value of the discharge in lit/sec.
Determine the flow in each of the pipes shown in the figure. Assume f=0.02 for all pipes. Problem 7-66 with the following conditions: - roughness coefficient for all pipes = 0.05 - elevation B = 100 m
Assume Cc=0.62 and cy=0.98, calculate the discharge through a 120-mm diameter orifice under a head of 6.5 m of oil (SG=0.88).
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
A small orifice in area is in the vertical side of a rectangular tank. The horizontal sectional area of the tank is 0.40 m2. At a given instant the head on the orifice is 1.2 m. and 312 sec. hater it is 0.6 m. a. Compute the value of the coeff. of discharge C b. Using a coeff. of discharge of 0.60, how long will it take to lower the water surface from 1.2 m. to 0.8 m. c. Using C = 0.60; what will be the height of water from 1.2 m. after a lapse of 240 sec.
A Venturi meter having a throat diameter of 150mm is installed in a 300mm diameter horizontal pipeline carrying oil (S = 0.80). A mercury U-tube connected as shown shows a difference in height of mercury columns of 200mm, the remainder of the tube being filled with oil. If the meter coefficient is 0.95, determine the following: a.)The theoretical discharge (m3/s). Consider HL = 0. b.)The actual discharge (m3/s). Consider HL c.)The head loss (m) between the inlet and the throat.
In differential equation Find the time to drain the tank completely (a) when c = 1.0 (b) when c = 0.65. If a horizontal cylindrical tank is 10 ft long and 2 ft in radius. A pipe with a nominal size of 1/2 inch schedule 10 is used as the outletix. The tank is initially 75% full of water.
The pipeline shown in the figure A. takes water from a reservoir and terminates in a nozzlehaving a jet diameter of 2 inches. With the pipe losses shown in the figure, and assuming anozzle loss of (a) 8.76 %, (b) 10.67 % of the velocity head in the jet. Compute the dischargeand make a table showing the elevation head, pressure head, and total head at each of thesix stations
Tank A has an elevation of 100 m and Tank B has an elevation of 160 m. Since Tank A is lower than B, engineers have installed a pump near A to transfer fluid to B. The discharge in the pipe is at 0.65 cubic meters per second and pipe has a length of 1 km. with a diameter of 0.6 meters. If Hazen williams coefficient is equal to 120, compute the head loss in the pipe.
2.A 25–mm diameter commercial steel pipe,50 m long,isused to drain an oil tank. Determine the discharge whenthe oil level in the tank is 5 m above the exit of the pipe.Neglect minor losses and assume f = 0.12.