19 Determine the net torque on the 5.0-m-long uniform beam shownin the figure (Figure 1).Figure65 N459P56 N30%6052 N1 of 1Part ACalculate about point C, the cm.Express your answer using two significant figures.TaboutC=SubmitPart BX Incorrect; Try Again; One attempt remainingIVE ΑΣΦ17Previous Answers Request AnswerCalculate about point P at one end. ATaboutP =Express your answer using two significant figures.SubmitIVE ΑΣΦ 110Previous Answers Request AnswerMacBook Air??m-Nm. N

Given data: The length of the beam d=5 m Along the 5 m uniform beam, at the two ends and in the…

Determine the net torque on the 5.0-m-long uniform beam shown in the figure (Figure 1). Figure 65 N 45° P 56 N 30° C 60° 52 N 1 of 1 > ▼ Part A Calculate about point C, the cm. Express your answer using two significant figures. TaboutC 17 Submit Part B 195| ΑΣΦ X Incorrect; Try Again; One attempt remaining Previous Answers Request Answer Calculate about point P at one end. TaboutP Express your answer using two significant figures. Submit IVE ΑΣΦ - 10 Previous Answers Request Answer M Incorrect Toi Aggior One attempt remaining ? ? m-N m.N

Determine the net torque on the 5.0-m-long uniform beam shown in the figure (Figure 1). Figure 65 N 45° P 56 N 30° C 60° 52 N 1 of 1 > ▼ Part A Calculate about point C, the cm. Express your answer using two significant figures. TaboutC 17 Submit Part B 195| ΑΣΦ X Incorrect; Try Again; One attempt remaining Previous Answers Request Answer Calculate about point P at one end. TaboutP Express your answer using two significant figures. Submit IVE ΑΣΦ - 10 Previous Answers Request Answer M Incorrect Toi Aggior One attempt remaining ? ? m-N m.N

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 4CQ: Which of the entries in Table 10.2 applies to finding the moment of inertia (a) of a long, straight...

See similar textbooks

Similar questions

What three factors affect the torque created by a force relative to a specific pivot point?
Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?
Rotational Inertia Problems 5 and 6 are paired. 5. N A system consists of four boxes modeled as particles connected by very lightweight, stiff rods (Fig. P13.5). The system rotates around the z axis, which points out of the page. Each particle has a mass of 5.00 kg. The distances from the z axis to each particle are r1 = 32.0 cm, r2 = 16.0 cm, r3 = 17.0 cm, and r4 = 34.0 cm. Find the rotational inertia of the system around the z axis. 6. N Use the information in Problem 5 to find the rotational inertia of the system around particle 1. FIGURE P13.5 Problems 5 and 6.
The precession angular velocity of a gyroscope is 1.0 rad/s. If the mass of the rotating disk is 0.4 kg and its radius is 30 cm, as well as the distance from the center of mass to the pivot, what is the rotation rate in rev/s of the disk?
What force must be applied to end of a rod along the x-axis of length 2.0 m in order to produce a torque on the rod about the origin of 8.0k Nm ?
A constant net torque is applied to an object. Which one of the following will not be constant? (a) angular acceleration, (b) angular velocity, (c) moment of inertia, or (d) center of gravity.
Consider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75
Which of the entries in Table 10.2 applies to finding the moment of inertia (a) of a long, straight sewer pipe rotating about its axis of symmetry? (b) Of an embroidery hoop rotating about an axis through its center and perpendicular to its plane? (c) Of a uniform door turning on its hinges? (d) Of a coin turning about an axis through its center and perpendicular to its faces?
A rigid body is rotating counterclockwise about a fixed axis. Each of the following pairs of quantities represents an initial angular position and a final angular position of the rigid body. Which of the sets can occur only if the rigid body rotates through more than 180? (a) 3 rad, 6 rad; (b) 1 rad, 1 rad; (c) 1 rad, 5 rad.
What are the necessary conditions for equilibrium of the object shown in Figure P12.1? Calculate torques about an axis through point O.
Figure P10.41 shows a side view of a car tire before it is mounted on a wheel. Model it as having two side-walls of uniform thickness 0.635 cm and a tread wall of uniform thickness 2.50 cm and width 20.0 cm. Assume the rubber has uniform density 1.10 103 kg/m3. Find its moment of inertia about an axis perpendicular to the page through its center. Figure P10.41
If you know the velocity of a particle, can you say anything about the particle’s angular momentum?