1) Determine the normal force at point C(Nc)Express your answer in pounds to three significant figures.2) Determine the shear force at point C(Vc).Express your answer in pounds to three significant figures.3) Determine the moment at point C.Mc Express your answer in pound-feet to three significant figures. Rod AB is fixed to a smooth collar D, which slidesfreely along the vertical guide shown in (Figure 1). PointC is located just to the left of the concentrated loadP=40 lb. Suppose that w = 11 lb/ft. Follow the signconvention.Figurepating< Previous3 ftascii_clock_plann....pdfw– 1.5 ft —A1 of 1130°

Answered: Image /qna-images/answer/73e9291b-ec52-42aa-bd65-c563729f47b8.jpg

Determine the normal force at point C(Nc) Express your answer in pounds to three significant figures. 2) Determine the shear force at point C(Vc). Express your answer in pounds to three significant figures. 3) Determine the moment at point C.Mc Express your answer in pound-feet to three significant figure

Determine the normal force at point C(Nc) Express your answer in pounds to three significant figures. 2) Determine the shear force at point C(Vc). Express your answer in pounds to three significant figures. 3) Determine the moment at point C.Mc Express your answer in pound-feet to three significant figure

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.10.10P: A cable and pulley system at D is used to bring a 230-lcg pole (ACB) to a vertical position, as...

See similar textbooks

Similar questions

A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A cable and pulley system at D is used to bring a 230-lcg pole (ACB) to a vertical position, as shown in the Figure part a. The cable has tensile force T and is attached at C. The length L of the pole is 6.0m, the outer diameter is d = 140 mm. and the wall thickness is t = 12 mm. The pole pivots about a pin at A in figure part b. The allowable shear stress in the pin is 60 MPa and the allowable bearing stress is 90 MPa. Find the minimum diameter of the pin at A in order to support the weight of the pole in the position shown in the figure part a.
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Ensssprrs wuii. Inside a helical spring of circular cross-section 20 mm in dimater spring is placed having the same cross-section. The mean radius of the outer spring is 80, that of the inner spring is S0 mm. Both the springs are of the same height and have 10 coils With a load being transmitted to both the springs they deflect by 50 mm. In which spring is the maximum shear stress greater, and what are their magnitudes? What is the corresponding load being transmitted? The shear modulus C = 80 GPa for both the spring materials.
A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?
Suppose that the assembled stiffness matrix of question 1 (as shown below) is as follows: [K]=108×a-a0-aa+b-b0-bb where a=4.06 N/m and b=2.28 N/m. If the applied force at node 3 is P=210 KN, find the displacement of node 2 in mm?
A solid steel shaft with an outsidediameter of 1.5 in. is supported in flexiblebearings at A and C as shown in FigureP15.43/44. Two pulleys are keyed to the shaft atB and D. Pulley B has a diameter of D B = 14 in.and belt tensions of T 1 = 100 lb and T 2 = 220 lb.Pulley D has a diameter of D D = 7 in. and belttensions of T 3 = 60 lb and T 4 = 300 lb. Lengthdimensions of the shaft are x1 = 8 in., x2 = 4 in.,x3 = 3 in., and x4 = 6 in. Determine the normaland shear stresses at point K on the shaft. Showthe orientation of these stresses on anappropriate sketch.FIGURE P15.43/44