2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at the position indicated.

2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at the position indicated.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.26P: The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A...

See similar textbooks

Related questions

Q: 450 B Dokg 45°

A: given:

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

Q: Refer to the diagram. a) Determine the horizontal and vertical components of force which the pin at…

Q: 2: Determine the force that the jaws J of the metal cutters exert on the smooth cable C if 100-N…

Q: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,…

Q: Determine the x-y and n-t components of the 31-kip force F acting on the simply-supported beam.

Q: The electric power transmission tower supports two wires that apply 18 kN vertical forces, and the…

A: ∑Fx=0; ∑Fy=0 & ∑MA=0so, Ax=-36kN; Ay=70.8 KN By=106.8KN

Q: In the assembly shown, rod AB is made of steel (E = 200 GPa) and has a diameter D = 50 mm. Rod BC is…

A: Given data: STEEL…

Q: Determine the force (written as a vector) which BC exerts on member AB (a) if the 600-N Iload is…

A: Given that , AB=1.4+1.4=2.8mθ=21°

Q: Determine the magnitude of the force 60 N supported by the pin at C of the loaded frame. 0.2 m 0.3 m…

A: If the force acting on pin at C is F then by considering vertical member DC, this force can be…

Q: A beam (AB) is supported by a roller at B and a pin at A. It is subjected to the following uniform…

A: Let us draw the reaction in free body diagram Using the conditions of the equilibrium in…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: A 300kg counterweight with center of mass at G is mounted on the AB crank rod of the oil pump unit.…

A: Given Data Torque supplied by motor is : M=250 Nm Mass of the counter weight mounted on crank AB…

Q: 3 Determine the force in each member of the truss. Note the presence of any zero-force members. Ans.…

Q: 3–13. A nuclear-reactor vessel has a weight of 500(10³) lb. Determine the horizontal compressive…

Q: 4/4 Determine the force in each member of the truss. Note the presence of any zero-force members. 5…

A: The free body diagram of the truss is as follows: Calculate the moment about point A as follows:…

Q: The 490-lb beam is supported at A and B when it is subjected to a force of P= 1000 lb as shown.…

Q: 200 - 400 200 N m D 200 F Dimensions in mm Determine the magnitude of the force (in N) of the…

A: As per given question We have to magnitude Of The force of given fig

Q: For the frame and loading shown, determine the components of all forces acting on member ABE.

A: Free body diagram of member BC: Moment about the point C: ∑MC=0 (↻+) (2400×1.2)-(By×2.4)=0By=1200N…

Q: Q1) Determine the design angle for strut AB so that the 400-lb horizontal force has a component of…

Q: 4. The rigid bar ABCD is supported by a pin at B and restrained by identic al ste el bars at C and…

A: First of all, make a FBD of the diagram as shown below.

Q: 5. The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the…

Q: Determine the horizontal and vertical components of force at pins A and D. D 2 m 0.3m A -1.5m- |B…

A: Free Body diagram

Q: If the roller at E is replaced by a pin support and the 30 kN force acting at joint H is a…

A: If the roller at E is replaced by a pin support, there will be total two pin supports (A and E) with…

Q: Q.1) (a) Draw individual free-body diagrams of the cylinder and members AB and BC shown below. Show…

A: "We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: weighs 8 kN/m. Determine the internal normal force in the post as a function of x. 2 m

Q: Determine the force P (magnitude of force P) required to support the 450 N force using the pulley…

Q: The vertical mast supports the 4-kN force and is constrained by two fixed cables BC and BD and by a…

A: The free-body diagram of the vertical mast is given as, The vector BD is written as, The unit…

Q: 2. Solve for the tensile force (in KN) acting inside the cable and the reaction (in KN) at hinge.…

A: Given: The values of G, M and L = 4,7 and 7 respectively

Q: Determine the value of the force in bar AB c the truss shown (N without decimals), enter a positive…

A: Given data:- b= 4m c = 3.5m a = 3m P1 = 600N P2 = 400N

Q: Determine the internal resisting forces and moment trans- mitted by section aa in Bar AB of the sign…

A: As it is given that the mass of the sign board is m=25 kg. The free body diagram for the beam is…

Q: Determine the internal forces at points F and G. F is located 0.7 m to the right of support A G is…

Q: Determine the horizontal and vertical components of force at pins A and D. D 2 m 0.3m A 1.5 m -1.5…

A: Given :- Determine the horizontal and vertical components of force at pins A and D.

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

Q: 2 m 0.3 m -1.5 m -1.5 m- 12 kN

Q: The pulley-cable system supports the 150-lb weight. The weights of the pulleys and the horizontal…

Q: Consider one end of a timber roof truss that is supported on a masonry wall. The reaction at the…

A: For the given condition,∑Fx=0F2cos25=F1F1=7cos25 kNF1=6.34

Q: D 2 m 0.3 m |A -1.5 m- -1.5 m E 12 kN

Q: 5. A 5-lb force is applied to the handles of the vise grip. Determine the compressive force…

A: Let∑ME=0⇒5(3+1)-FcD[1+0.7532+(1+0.75)2]×1=0⇒20-FcD[1.753.4731]×1=0⇒FcD=20/0.5038FcD=39.69 lb

Q: Angled member ABC is supported by being pinned to a collar on a smooth rod at A, a roller at B, and…

Q: E = 200 GPa A = 300 mm2 L= 3 m P. A 2 m 2 m D BO 1.5 m 3.0 m

Q: The post weighs 8 kN>m. Determine the internal normal force in the post as a function of x.

Q: Determine the magnitude of the force which member CD exerts on the pin at C. A 24° B 0.38 m Answer:…

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

A: Option B is correct.

Q: А 3 m C 3 m D B В 5 m 5 m- V 2 kN

A: Given Two forces of 2 kN is applied at C and D FBD of the figure

Q: An overhead crane is used to reposition the boxcar within a railroad car-repair shop. If the boxcar…

A: (a) Tension in the cable, T = 597.658 lb. (b) Angle between the cable and the x-y plane, θxy =…

Q: The press shown is used to emboss a small seal at E. Determine the required force P that will…

Q: The structure below supports a 4-kN force. It is constrained by the cords BC and BD and by a…

Q: Determine the horizontal and vertical components of force which the pin at B exerts on member BC of…

Q: 4/16 The rectangular frame is composed of four perim- eter two-force members and two cables AC and…

A: To Find : The forces all members due to the load L in position a and b. FBD: Free body diagram :

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

30 cm
18 cm
Hom
Scm
Hom
Sum
2. The 30 cm handle is connected rigidly to the 5cm bar at a right angle. Determine the force
developed at A if a force P = 100 N is applied perpendicular to the handle when the handle is at
the position indicated.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given Data:

VIEW

The angle of inclination of the handle from vertical:

VIEW

Force developed at A:

VIEW

Result:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 50-m steel surveying tape has a mass of 1.6 kg. If the tape is stretched between two points at the same elevation and pulled until the tension at each end is 60 N, determine the horizontal distance between the ends of the tape. Neglect the elongation of the tape due to the tension.
Determine The Forces P F T Required To Keep The Triangular Frame Inequilibrium.
the homogeneous cylinder of weight W=100 N rests in a frictionless right angled corner. determine the contact forces NA and NB angle is 30 degrees
The system is made up of a bar, supported by a pin at point A and by a smooth collar at point B (the collar slides on the ABG bar). The collar is pinned to bar BDE, and bar BDE is supported by a pin at D and a cable at end E. Determine the force P such that the force in the cable equals to T. With T= 26 lb, a=4 in, b=9 in
the cylinder with a mass of 1000 Kg is supported as shown in the figure, determine the reaction at the hinge.
an arrangement inwhich four disks are suspended by cords.Thelonger, top cord loops over a frictionless pulleyand pulls with a force of magnitude 98 Non the wall to which it is attached.The tensionsin the three shorter cords are T1 = 58.8 N,T2 = 49.0 N, and T3 = 9.8 N. What are themasses of (a) disk A, (b) disk B, (c) disk C,and (d) disk D?
2-D PROBLEM: A spherical tank with a radius of 3.41m that has a mass of 28928.644kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following: β: 21.774° θ: 46.452° 1. The reaction @ point D. 2. Tension @cable BE 3. The x and y-component of the reaction @ A 4. The reaction @ A
A.The bar of negligible weight is supported by two springs, each having a stiffness k = 98 N/m. If the springs are originally unstretched, and the force is vertical as shown, determine the angle the bar makes with the horizontal, when the 31-N force is applied to the bar. B.Determine the stiffness k of each spring so that the 32-N force causes the bar to tip = 13.6° when the force is applied. Originally the bar is horizontal and the springs are unstretched. Neglect the weight of the bar.
The jib crane is fixed at (A) and carry a box of ( 2500 kg ) mass, as shown in the figure. Determine the reactions on the jib crane at point ( A ). 60 5 m 7 m
A 200 lb rock is being lifted by a pry bar. Determine the force “P” required to lift the rock into the position show.
The frictionless slider B has a frictionless pulley mounted to it, around which is wrapped a cable that supports weight W = 180 lb as shown. The pulley at D is also frictionless, and member BE is a bar. If α = 55° determine the force in bar BE.
Three cylinders are piled in a rectangular ditch as shown. The radius of the uppermost cylinder is 7cm, the middle one is 9cm, and the botom cylinder is 4cm. The ditch has a length of L - 20cm. Assume that the weight of the cylinders are W1 = 24kN, W2 = 44kN, and W3 = 18kN. Determine the reaction (kN) at A. Neglectt friction.