Determine the output of the DAC in Figure 14-19(a) if the waveforms representing a scquence of 4-bit binar numbers in Figure 14-19(b) are applied to the inputs. Input Do is the least significant bit (LSB). 40 kl D, W RE 0 1 2 3 4 56 7 8 9 1011 1213 14 15 20 kn +5 V Do +5 V 0- +5 V 10 k2 OV Dr +5 V 5 kn D,0 W Dy (a) (b) FIGURE 14-19

Determine the output of the DAC in Figure 14-19(a) if the waveforms representing a scquence of 4-bit binar numbers in Figure 14-19(b) are applied to the inputs. Input Do is the least significant bit (LSB). 40 kl D, W RE 0 1 2 3 4 56 7 8 9 1011 1213 14 15 20 kn +5 V Do +5 V 0- +5 V 10 k2 OV Dr +5 V 5 kn D,0 W Dy (a) (b) FIGURE 14-19

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter29: Automatic Starters For Star-delta Motors

Section: Chapter Questions

Problem 4SQ: The closed transition contactor is energized only on transfer from star to delta. How is this...

See similar textbooks

Similar questions

19. The OTA in Figure 14-58 functions as an amplitude modulation circuit. Determine the output voltage waveform for the given input waveforms assuming K = 16 μS/MA. 100 mV 500 kHz Vin o VMOD +8 V +6 V-- +4 V-- +2 V- +1 V- 0 R₁ www 10 ΚΩ www III R₂ 10 ΚΩ 0 10 με 20 με 30 με 40 με 50 με VMOD +9 V OTA -9 V FIGURE 14-58 RBIAS 39 ΚΩ ww III RL out 10 ΚΩ
If you want to converta 2 V DC signal to 10 V DC signal, then the values of R, and Rz should be R1=10k2, R2=2k0 R1=2kQ, R2=10KQ R1=10kn, R2=5k0 R1=5k0, R2=10k0
24VO Find t CI HH b) WT 4+ C2 C6 a.) CT, If C₁ = 1MF C₂2nF J C3 = 4mF₁ C₂ = SMF C5 = 2nF c.) Elastance (TN) J CG= 0.5 F
A received signal power of begin mathsize 14px style negative 90 d B end style is equal to ? negative 100 d B subscript m negative 120 d B subscript m negative 60 d B subscript m None
Add an Enable Signal to this Counter's diagram On Op D INC +1 DEC OPC CLK RST T -0
| sketeh out the follewing signals: (a=5, b=3, c=2) a-) V = 15a(sin21000*ct) b-) V = 3b(cos(r500*ct)+3) c-) Assume that you measure the signal V1 using Digital Volt Meter(DVM) and ossiloscope. What will you read on the DVM display and oscilloscop dispaly when the input voltages are defined as 1-) V = 15a(sin2m1000*ct) 2-) V = 3b(cos(7500*ct)+3) Write down and sketch all the voltages for each case. Show all parameters, including period and maximum values of the signals. aR V AC aR V, aR What will you read at the DVM display when you read the voltages at AC mode What will you read at the DVM display when you read the voltages at DC range
Change the MOD-8 counter in Figure to a MOD-16 counter, and connect the MSB to the multiplexer E input. Draw the Z waveform. 1 ΚΩ +Vcc W 13 1₂ lo Eight-input multiplexer 74HC151 SSS 17 $₂ S₁ So MOD-8 CLK- counter •JMM
4. (d) the eedba Calculate the oscillator frequency. Determine the necessary value of R₂ in Figure 16-57 so that the circuit will oscillate. Neglect the forward resistance of the zener diodes. (Hint: The total gain of the circuit must be 3 when the zener diodes are conducting.) Explain the purpose of R3 in Figure 16-57. R₁ 100 kQ R2 www ww-l R$ 1.0 ΚΩ D₁ t 6.8 V 6.8 V R3 www 47 kQ enfren D₂ www ‡ www. C₁ 0.015 F R$ WWW 1.0 kn C₂ 0.015 F V₁
[BX]=[150]2-CL-CH÷DI BX=4444 H [150]=110 CX=64D8 H DI =04 H
Draw the small signal equivalent circuit of the following circuit: VI O Vdd T RL M1 M2 -O vo
Find the state graph for the following parallel counter: C To Q. QA TB QB TA A QB clk clk clk
From the circuit below : B- Cin- Du Cout a. From the input signal A,B,Cin draw the output signal S and Cout b. If possible, simplify the circuit and draw the simple circuit INPUT A- INPUT B INPUT C- in OUTPUT ? Cout