Q5- Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (W0-W9) with one terminal connected to Vcc. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with "a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f 18 a a e b d

Q5- Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (W0-W9) with one terminal connected to Vcc. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with "a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f 18 a a e b d

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.22P

See similar textbooks

Similar questions

Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
Hi my professor (signal and system analysis ) give me this screenshoot to understand but i don't know what the subject or how to slove it can you help understand . Thank You .
Give me right solution otherwise leave it. A voltage signal with a range of zero to 115 V. is to be converted by means of an ADC. Determine the minimum number of bits required to obtain a resolution of 10V?
What can you say about AM DSB-FC, AM DSB-SC, and AM SSBSC? What do they have in common and their difference? Please explain really well
plz solve this signal and system subject ...
2)Convert 11011010100100012 to hexadecimal. A)895B B)CA11 C)53AC1 D)DA91
Design a sequential circuit (overlapping) with an input ‘x’. The pattern to be detected is the binary number that is equal to 1001100 For example,the circuit detects the sequence 00010 . When the sequence is detected, the detector outputs z=‘1’ For this circuit: Draw the ASM diagram.
Subject: Digital electronics Plz solve this Question
This was a part of a solution set given to me in bartleby. I wanted to know if my speculations of this being miswritten is correct. The red indicates what i think should be a 0 and the blue indlcates what i think should be 1. if i am wrong please let me know how to understand the kmaps better?
Design a counter that will output 0, 2, 1, 3 and repeat again. P.S. I expect an answer like you had done at this similar question: https://www.bartleby.com/questions-and-answers/design-a-counter-that-will-output-1-2-3-5-8-13-and-repeat-again./6438422d-04f0-4a28-bca6-87a7f045d9d6
A2 Briefly, but informatively, describe importance laser ablation in combination with ICP-MS in solid sample. Cite Reference/s
The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the voltage level applied to the ADC input is 1.67 V, what is the numerical value read? For numbers with commas, take 4 digits after commas.