Determine the overall heat loss and the temperature profile at each interface of the following composite cylinder: TA = temperature of gas inside the kiln ha = convective heat transfer coefficient of gas TB = ambient temperature he convective heat transfer coefficient of ambient air TB = 80 K hB = 4 W/m²K TA = 1000 K ha = 30 W/m²K K = 2.05 W/m.K K = 52 W/m.K 6 m 2 m 1.9 m,

Determine the overall heat loss and the temperature profile at each interface of the following composite cylinder: TA = temperature of gas inside the kiln ha = convective heat transfer coefficient of gas TB = ambient temperature he convective heat transfer coefficient of ambient air TB = 80 K hB = 4 W/m²K TA = 1000 K ha = 30 W/m²K K = 2.05 W/m.K K = 52 W/m.K 6 m 2 m 1.9 m,

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.8P

See similar textbooks

Similar questions

Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
You are asked to design a metal hot dog holder for roasting hot dogs over an opencampfire. The holder is to be designed such that while the end holding the hot dogbecomes cherry red (1400oF), the other end can still be held without using aninsulated handle or glove (~95oF). Design it such that it can be used even on awarm, still day, Tf = 90oF (Assume the convective heat transfer coefficient, h, fora horizontal cylinder is uniform over the whole cylinder and equal to 4.0Btu/hrft2oF)
What is heat transfer coefficient?
An industrial freezer is designed to operate with an internal air temperature of -20°C when the external air temperature is 27°C, and the internal and external heattransfer coefficients are 8 W/m2 -K and 12 W/m2 -K, respectively. The walls of thefreezer are composite construction, comprising an inner layer of plastic (k = 0.33 W/m-K, and thickness of 10 mm), and an outer layer of stainless steel (k = 15 W/m-K, and thickness of 3 mm). Sandwiched between these two layers is a layer of insulation material with k = 0.07 W/m-K. Find the width (mm) of the insulation thatis required to reduce the convective heat loss to 60 W/m2.
Discuss the significant and industrial application of heat transfer from extended surface (fins).
J 5 A cylindrical steel tank with a diameter of 1.8m and a height of 2m, is insulated with polyurethane on its lateral faces and its lid. The insulation is 40 mm thick and covered with a thin layer of metal. The tank contains water that is kept warm by an electric heater in such a way as to maintain the inner surface of the tank at a temperature of 55C. The ambient air temperature is 10C and the external skin coefficient is 10 w/m2K. If the energy cost is $0.15/kwh. What is the monthly energy cost for water storage?
What is the heat transfer coefficient for ambient air at 43 C
The wall of a 5 m high cylinderical steel tank (ks= 20 W/mK) of inner diameter 1.5 m and 200 mm thick contains hot oil at 100 C. On the outside of the tank 12 mm of spray urethane insulation is added to stop the oil from cooling. If the worst outside temperature is -6 , (hi = 16 W/m^2 K) and (ho = 5 W/m^2 K) how much heat needs to be added to keep the tank at 100 C for pumping reasons and what are the overall heat transfer coefficients Uo and Ui?
Plot how hx (heat transfer coefficient) depends on the distance along a plate (x) and explain how this relationship .
Calculate the quantity of heat conducted per minute through a duralumin circular disc 119mm diameter and 22.65mm thick when the temperature drop across the thickness of the plate is 9.3°F take the coefficient of thermal conductivity of duralumin as 150 W/m-K. Answer: 22.833 kJ/min
When the convection heat transfer coefficient is very large (h → ∞), the convection resistance becomes zero and Ts ≈ T. This situation is approached in practice at surfaces where ------------------------ occur.
What are the key factors that influence the convective heat transfer coefficient in a mechanical system, and how can engineers optimize these factors to enhance heat transfer efficiency?