Determine the power absorbed by a clutch rotating at an average speed of 3100 rpm. the outer diameter is 20 cm and the inner diameter is 15 em. The coefficient of friction is 0.26 and the pressure is 0.1 N/mm. Also find the amount of heat produced if clutching takes 5 seconds. Assume it is new clutch (uniform pressure). Single disc or plate Friction surface

Determine the power absorbed by a clutch rotating at an average speed of 3100 rpm. the outer diameter is 20 cm and the inner diameter is 15 em. The coefficient of friction is 0.26 and the pressure is 0.1 N/mm. Also find the amount of heat produced if clutching takes 5 seconds. Assume it is new clutch (uniform pressure). Single disc or plate Friction surface

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder with an area ratio of 0.2 and a bore diameter of 8.0 cm steadily extends a 13.3 kN load. If the cap-side pressure is 4 MPa and the rod-side pressure is 250 kPa, what is the force efficiency of the actuator? Also, what is actuator efficiency in %?
1. The machine B is belt-driven by the electric motor A that has an efficiencyof 85%. When the motor is running at 25 rad/s, the tension in the upper part of thebelt is 90N greater than in the lower part. Determine the power consumption of the motor in horsepower (hp). 2. When the system described in Prob. 18.9 is running at 40 rad/s, the powerconsumption of the motor is 2.4 hp. Calculate the torque in (a) the output shaft of motor A; and (b) the input shaft of machine B.
.A steam engine develops power at mean torque of 18,000 N-m and velocity of 9 m/s. The mean diameter of the flywheel rim is 1.3 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
The drive is by V-belts from an electric motor running at 1500 r.p.m. A compressor, requiring 75000W is to run at about 500 r.p.m. The diameter of the pulley on the compressor shaft must not be greater than 1.2 meter while the centre distance between the pulleys is limited to 1.85 meter. The belt speed should not exceed 1500 m/min. Determine the number of V-belts required to transmit the power if each belt has a cross-sectional area of 3 cm2, density 1100 kg/m3 and an allowable tensile stress of 3 MPa. The groove angle of the pulley is 50°. The coefficient of friction between the belt and the pulley is 0.3. Calculate also the length required of each belt.
A train of mass 200 tonnes moves on a level track having a track resistance of 85 Newtons per tonne. Find the maximum speed of the engine, when the power developed is 320 kW.
A press tool machine uses a flywheel in the form of a solid steel disc 0.7 m diameter and 0.1 m thick rotating with a mean speed of 60 rev/min. The density of the steel is 7830 kg/m^3. The press is operated once every 5 revolutions and a torque of 2000 Nm is exerted on the tool for a duration of 0.05 seconds. determine the following: The energy absorbed is replaced during the rest of the cycle. The coefficient of fluctuation of speed .The maximum and minimum speeds of the flywheel
list down the derivation of formulas and describe each variable of "Work and Energy" (Dynamics of rigid bodies)
Given that the compressor's energy input is 2100 kJ and the heat provided is 3500 kJ. The area is reported as 0.08m with a diameter of 0.2050 m. To get the energy balance, solve for the Energy In.
What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in the figure shown in the image below when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume p = 1.05 kg m3.
A belt drives a pulley of 200mm diameter such that the ratio of tensions in the tight side and slack side is 1.2. If the maximum tension in the belt is not to exceed 240KN. Find the safe power transmitted by the pulley at a speed of 60rpm.
What thrust is obtained from a propeller 3 m in diameter that has the characteristics given in Fig. 14.2 when the propeller is operated at an angular speed of 1400 rpm and an advance velocity of zero? Assume p = 1.05 kg m3.
Find the speed of shaft driven with the belt by an engine running at 600RPM. The thicknessof belt is 2cm, diameter of engine pulley is 100cm and that of shaft is 62cm..