Answered: Determine the pressure in a vessel of…

Name: Determine the pressure in a vessel of mercury at a point 400mm below t
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the pressure in a vessel of mercury at a point 400mm below the liquid surface, expressing the answer in kPa absolute.

Engineering

Mechanical Engineering

Determine the pressure in a vessel of mercury at a point 400mm below the liquid surface, expressing the answer in kPa absolute.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 14RQ: Atmospheric pressure at sea level under standard conditions is ______inches of mercury (Hg) or_____...

See similar textbooks

Related questions

Q: 7. A polished metal pipe 5 cm outside diameter and 370 K temperature at the outer surface is exposed…

Q: Refrigerant 134 A enters in a condenser of a heat pump at 180 kPa and -4 0C and exits with a quality…

A: Refrigerant=R134a Condenser pressure, Pc=180 kPa Condenser inlet temperature, T2=-4oC Quality of…

Q: Adjusting rear camber is the first step in the four-wheel alignment process. What are the components…

A: given; adjusting rear camber is the first step in the four wheel alignment process. what are the…

Q: The following are true about the factors important for sand mold selection, except: O Good…

Q: A flanged bolt coupling is used to connect a solid shaft 85 mm in diameter to a hollow shaft 100 mm…

Q: Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters…

Q: Determine the moment of inertia of the shaded area about the x-axis in two different ways. 3.0a a a…

Q: The 499-N force is applied to the 102-kg block, which is stationary before the force is applied.…

A: Given data: P=499 Nm=102 kgθ=36°μs=0.65μk=0.43 Need to determine the magnitude and direction of…

Q: 1. In the figure below (Figure 1), d and h can be computed from the angle 0 and the side s. Figure…

A: Given data s = 1000.000 m θ = 20°00'00" Error in measuring s = 0.100 m Error in measuring θ = 20"

Q: Question 2 In reference to Figure 2.1, show that head addition to a process is a function of…

Q: A steady flow compressor handles 113.3 m3/min of air measured at intake where p1 = 97.22 kPaa and t1…

Q: S. Fig Q5 shows a shaft of gearbox rotating about x axis. Shafi BC is a solid shalt with dircular…

Q: Determine the coordinates of the centroid of the shaded area. 140 mm- 140 mm - 100 mm- 110 mm 40 mm…

A: Let's divide the given shaded into three parts. Rectangle: Breadth, b= 140+140= 280 mm Height, h=…

Q: Hello! Can you please elaborate the solution for letter b?

Q: Consider a water-ammonia binary vapor cycle consisting. In the steam cycle, superheated vapor enters…

Q: C. (Round off to 3 decimal places) The length of a base line was measured using two different EDM…

A: Given data The measurements made by two instruments are: We have to find the…

Q: If the allowable shear stress for each of the 0.30-in.-diameter steel pins at A, B, and C is 13 ksi,…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral 30 71…

A: To determine the coordinate of the centroid of the composite area.

Q: applied. Use k1 - 12.67 N/m, k2 - 11.1 N/m, k3 - 28.39 N/m, and k5 - 33.91 N/m. (Use 2 decimal…

Q: The 21-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.5 m. If it is…

A: Given Givenm=21kgL=0.5mM=78Nmθ=45o=π4

Q: A 3.00 kg block is pushed against a spring with negligible mass and force constant k = 500 N/m,…

Q: The truss is composed of equilateral triangles of side a = 2.4 m. The load is L= 400 N. Determine…

A: Given a = 2.4 m L = 400 N To find Magnitude of force BC Magnitude of force CG

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 9" 4" 7" 6" - 8" 11"-…

Q: Determine the forces in members BC and BG of the loaded truss. The forces are positive if in…

Q: An otto cycle operates in 0.1lbs/s of air from 13psia and 140°F at the beginning of compression. The…

Q: The kinematic viscosity of the fluid depends on O 1. Surface tension O 2. Vapor pressure 3. None of…

A: The kinematic viscosity of the fluid depends on Answer: 4. Fluid temperature

Q: The 30-kg uniform thin hollow square plate is pinned at point 0, and its side L = 0.2 m. If it is…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Steam enters the first turbine stage of a vapor power cycle with reheat and regeneration at 32 MPa,…

A: Answer: consider the enthalpies of each stage in the cycle as follows: h1 = h@ 32MPa,600°C = 3423.8…

Q: ermine the magnitudes of all pin reactions for the frame loaded as sh ume F-860 N, a - 695 mm, b -…

Q: Calculate the y-coordinate of the centroid of the shaded area. The triangle is equilateral. 30 71 91…

Q: Steam at a pressure of 1000 psia and 650 0F enters an adiabatic turbine and leaves at 75 psia. The…

Q: The truss is composed of equilateral triangles of side a = 2.4 m. The load is L = 210 N. Determine…

Q: k1 k1 k4 k2 k3 ks F

A: GIVEN DATA- A SPRING SYSTEM GIVEN F=62.11N WE HAVE TO FIND EXTENSION

Q: A cascade refrigeration system serves a 75 ton evaporator at 119.4 KPa. The system uses direct…

A: Cooling capacity, Q˙e=75 ton=75*3.25=264 kW 1 TR=3.52 kWAt 119.…

Q: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of…

Q: Uniform internal heat generation at q =6.0×10^7 W/m3 is occurring in a cylindrical nuclear reactor…

A: Given, Internal rate of heat generation = q˙g = 6 x 107 W/m3 Diameter of fuel rod = d = 60 mm…

Q: Determine the percent reductions in both area and area moment of inertia about the y-axis caused by…

Q: The man pushes on the roller with force P through a handle that connects to the central axle of the…

A: Gggg

Q: Air is compressed in an adiabatic compressor from 55 psia and 660 R to 270 psia and 1200 R.…

A: Given Initial pressure, P1 = 55 psia Final pressure, P2 = 270 psia Find Isentropic efficiency

Q: A steel band 8mm thick is to be pulled on to a cylinder 30cm in diameter. The internal diameter of…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: In a free vortex, the velocity, at point A at a radius of 0.125 m, is measured to be 2 m/s. What…

Q: Water is the working fluid in an ideal Rankine cycle. Steam enters the turbine at 1400 lbf/in2 and…

A: Given data Conditions of steam at turbine entry : 1400 lbf/in2 and 1200°F Condenser Pressure = 2…

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

Q: The 27-kg uniform thin hollow square plate is pinned at point O, and its side L = 0.2 m. Determine…

A: When an amount of force act on the object, it has the tendency to rotate the object about the point,…

Q: The variable h designates the arbitrary vertical location of the center of the circular cutout…

Q: Determine the force in member AE of the loaded truss. The force is positive if in tension, negative…

Q: The following properties for Freon-12 were obtained. At -22 °C b (superheat) = 353 KJ/kg ha = 343…

A: The refrigeration effect is the amount of heat that is required to extract from the storage space in…

Topic Video

Question

Determine the pressure in a vessel of mercury at a point 400mm below the liquid
surface, expressing the answer in kPa absolute.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
If the local atmospheric pressure is 1bar, determine a. Absolute pressure in kPa if Pg =900torr
Determine the pressure in a vessel of mercury (spec. gr.= 13.6) at a point 8 inches belowthe surface expressing the answer in a.) pounds per square foot, and b.) pounds per squareinch.a. Write the given and required.b. Illustration of the problemc. Solution
A manometer containing mercury with density, ρ = 13,600 kg/m3 is attached to a tank filled with air. The mercury-level difference between the two columns is 80 cm. Questioni)Determine the absolute pressure of the air in the tank if the atmospheric pressure is 98 kPa. Use gravitational force, g = 9.81 m/s2.
Determine the height of mercury in mm of Hg for a manometer if the gauge pressure is 99.84 kPa and the density of mercury is 13,570 kg/m3
The barometric pressure reading at sea level is 760 mm of mercury while that on top 735 mm. if the density of air is assumed constant at 1.2 kg / (m ^ 3) ,calculate the elevation of the mountain top?
Determine the pressure of compressed air in an air vessel if the manometer mounted on it shows a pressure of 3 m of mercury. Assume density of mercury to be 13.6×10^3 kg/m^3 and atmospheric pressure as 101 kpa
Determine the pressure exerted on the surface of a submarine cruising 225 ft below the free surface of the sea. Assume that the barometric pressure is 14.7 psia and the specific gravity of seawater is 1.03.
A vacuum gauge connected to a chamber reads 42.4 kPakPa at a location where the atmospheric pressure is 94 kPakPa. Determine the absolute pressure in the chambe
consider the figure shown. Determine the pressure at point A if the tank contains a liquid with specific gravity of 0.957 and if the mercury from point D to E in the manometer has density of 13,550 kg/m^3. Report final answer in Pascal (Pa). Use specific weight of water as 9.81 kN/m^3
A U-tube manometer filled with mercury is attached to a gas tank. The level ofmercury on the open end of the manometer is 40 cm higher than the level at theend attached to the tank. What is the gage pressure of the gas inside the tank? a) what is the absolute pressure of the gas inside the tank? b) if the level of mercury on the open end is 60 cm lower than the level atthe end attached to the tank, what is the absolute pressure of the gas?
The pressure in a natural gas pipeline is measured by the manometer shown in Fig. with one of the arms open to the atmosphere where the local atmospheric pressure is 14.2 psia. Determine the absolute pressure in the pipeline