Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1527 kJ is supplied to saline water in the steam generator to heat from 21 to 101°C for the generation of water vapor, Take the density & specific heat of the solution as 1014 kg/m' & 3.3 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m)

Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1527 kJ is supplied to saline water in the steam generator to heat from 21 to 101°C for the generation of water vapor, Take the density & specific heat of the solution as 1014 kg/m' & 3.3 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

1. Saturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.
An inventor claims to have devised a process using only saturated steam at 100C which by a complicated series of steps, make heat continuously available at T of 177C. He claims further that, for every kilogram of steam taken into the process, 1800 kJ of energy as heat is liberated at this higher T of 177C. Show whether or not such a process is possible. In order to give the inventor the benefit of any doubt, assume cooling water to be available in unlimited quantity at 0C. topic: introduction to chemical engineerint thermodynamics
Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1738 kJ is supplied to saline water in the steam generator to heat from 26ºC to 111ºC for the generation of water vapor, Take the density & specific heat of the solution as 1031 kg/m3 & 3.6 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg) Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3
Find the dryness fraction of a steam having a specific volume of 15 m3 /kg after expansion in a turbine. The specific volumes of saturated liquid and saturated vapor corresponding to the pressure are 0.001 m3 /kg and 15.25 m3 /kg, respectively.
An electric windshield defroster is used to remove 0.25-in of ice from a windshield. The properties of the ice are Tsat = 328F, uif = hif = 144 Btu/lbm, and v = 0.01602 ft3/lbm. Determine the electrical energy required per square foot of windshield surface area to melt this ice and remove it as liquid water at 328F. What is the minimum temperature at which the defroster may be operated? Assume that no heat is transferred from the defroster or ice to the surroundings.
A 14-ft3 tank contains oxygen initially at 14.7 psia and 80°F. A paddle wheel within the tank is rotated until the pressure inside rises to 20 psia. During the process 20 Btu of heat is lost to the surroundings. Determine the paddle-wheel work done. Neglect the energy stored in the paddle wheel. The gas constant and molar mass of oxygen are R = 0.3353 psia·ft3/lbm·R and M = 32 lbm/lbmol. The specific heat of oxygen at the average temperature of Tavg = (735 + 540)/2 = 638 R is cv ,avg= 0.160 Btu/lbm·R. The paddle-wheel work done is Btu. ANSWER
A cylindrical vessel (D=98,4 cm) is filled with water (ρ=1000 kg/m3, c=4.187 kJ/kg.K) to a depth of 113,64 cm. The initial temperature of the water is 15°C. Determine the time [min] required to increase the water temperature to 50°C when it is immersed into tank, filled with oil at 105°C. (NOTE: The overall heat transfer coefficient between the oil and the water is 284 W/m2.K. The surface area is 4.2 m2.)
A heat-insulated (adiabatic) constant volume vessel divided by a metal curtain. The volume of the compartments is not equal!. Initially, one of the chambers contains 2.5 kg of compressed s-phase water at a temperature of 60 °C and a pressure of 600 kPa. The other chamber is empty (vacuum). Then the metal curtain is lifted and the water covers the entire volume. Since the final pressure is 10 kPa, calculate the volume of the container and the final temperature of the water
Determine the MW and specific heat ratio of a gas whose Cv=1.386 kJ/kg.K and R= 0.485 kJ/Kg.K
A 10 ft³ vessel of hydrogen at a pressure of 300 psia is stirred by paddles until the pressure becomes 400 psia. Determine (a) ⧍U and (b) W. No heat is transferred, cv = 2.434 Btu/lb R Ans: ⧍U = 434 Btu; W = -434 Btu
Q1) a) A river flowing steadily at a rate of 240 m3/s is considered for hydroelectric power generation. It is determined that a dam can be built to collect water and release it from an elevation difference of 50 m to generate power. Determine how much power can be generated from this river water after the dam is filled. (b) A piston–cylinder device initially contains 50 L of liquid water at 40°C and 200 kPa. Heat is transferred to the water at constant pressure until the entire liquid is vaporized.i. What is the mass of the water?ii. What is the final temperature?iii. Determine the total enthalpy change
An electric water heater has a capacity of 2 liters. In this heater, the water is initially found as a saturated liquid at 150 kPa. When the water is in this state, the heater automatically turns on and heats the water, which expands at a constant pressure through a movable cover mechanism at the top of the heater, which has an associated work done by the system (Ws). Additionally, the electrical resistance supplies 2.2 MJ to the water. These types of heaters have very good thermal insulation and the surroundings are at normal conditions (25°C and 100 kPa). Based on this information: a) Determine the states of the working substance. b) Determine the minimum work (Wmin) with which the process can be carried out. c) Determine the exergy destroyed during this process.