3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to adepth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and adownward acceleration, ay, equal to 3 m/s2.If after the acceleration, the oil depth is 1.5 m, determine the value of ax. Assumeа.unit width.b.Calculate the pressures at A and B during the acceleration.3 m3 mOIL2 mB3 m4 m3 m

Name: 3. The open trapezoidal tank shown in the figure is initially filled
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to adepth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and adownward acceleration, ay, equal to 3 m/s2.If after the acceleration,

Engineering

Mechanical Engineering

3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to a depth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and a downward acceleration, ay, equal to 3 m/s?. a. If after the acceleration, the oil depth is 1.5 m, determine the value of ax. Assume unit width. b. Calculate the pressures at A and B during the acceleration. 3 m 3 m OIL 2 m A В 3 m 4 m 3 m

3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to a depth of 2 meters. It was subjected to an unknown rightward acceleration, ax, and a downward acceleration, ay, equal to 3 m/s?. a. If after the acceleration, the oil depth is 1.5 m, determine the value of ax. Assume unit width. b. Calculate the pressures at A and B during the acceleration. 3 m 3 m OIL 2 m A В 3 m 4 m 3 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two very large open tanks A and F (Fig. ) containthe same liquid. A horizontal pipe BCD, having a constriction at C andopen to the air at D, leads out of the bottom of tank A, and a verticalpipe E opens into the constriction at C and dips into the liquid in tank F.Assume streamline flow and no viscosity. If the cross-sectional area atC is one-half the area at D and if D is a distance h1 below the level ofthe liquid in A, to what height h2 will liquid rise in pipe E? Express youranswer in terms of h1.
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1, sg2=1, sg3=1, and h1=0 m, h2=0 m, h3=0 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
To determine the shear stress of oil, two horizontal plates are placed 15 cm apart, the space between them is filled with the oil of viscosity 15 poise. If the upper plate is moving with velocity 2,000 mm/s, find the shear stress (τ).
A tank of water 5m deep receives a constant upward acceleration az= 4 m2/sec, determine the gauge pressure at the tank bottom in pascal is: *
An open tank 5m long, 2m deep and 3 m wide contains oil of relative density 0.9 to a depth of 0.9 m. If the tank is accelerated along its length on a horizontal track at a constant value of 3 m/s2 , determine: (i) The new positon of the oil surface. (ii) The pressures at the bottom of the tank at the front and rear edges. (iii) The amount of spill if the tank is given a horizontal acceleration of 4.5 m/s2 instead of 3 m/s2 .
U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in the U - tube has a density: p2= 2000 kg/m3. The height a = 10 cm and h = 15 cm. If the pressure at point ① is 111 kPa, what is the pressure at point ② ?
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Q6) The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine
A open tank 5 m, long, 2 m deep and 3 m wide contains oil of relative density. 0.9 depth of 0.9 m if the tank is accelerated along its length on a horizontal track at a constant value of 3 m/second, square determine the new position of oil surface.
plzzzzzzzz heeeelp meeee right nowww What would be the rotation rate (in rad/sec) if during rotation the water in the right leg (with a diameter of d) decreases a distance h1=0.10 m?
The water level in the 1.8 m high and 1 m diameter cylindrical tank in the figure is 1.4 m. If this tank is rotated around its own axis at what speed will the axial depth be zero? (In other words, what is the number of revolutions at which a dry area will begin to form at the bottom of the tank?) Take the gravitational acceleration as 10 m / s2 and π as 3.