Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1590 kJ is supplied to saline water in the steam generator to heat from 26°C to 118°C for the generation of water vapor, Take the density & specific heat of the solution as 1011 kg/m³ & 3.4 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m?)

Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1590 kJ is supplied to saline water in the steam generator to heat from 26°C to 118°C for the generation of water vapor, Take the density & specific heat of the solution as 1011 kg/m³ & 3.4 J/kg°K respectively. Solution: Change in Temperature (in K) Mass of the saltwater (in kg) Quantity (Volume) of saltwater (in m?)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

Find the dryness fraction of a steam having a specific volume of 15 m3 /kg after expansion in a turbine. The specific volumes of saturated liquid and saturated vapor corresponding to the pressure are 0.001 m3 /kg and 15.25 m3 /kg, respectively.
Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1738 kJ is supplied to saline water in the steam generator to heat from 26ºC to 111ºC for the generation of water vapor, Take the density & specific heat of the solution as 1031 kg/m3 & 3.6 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg) Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3
1. Saturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.
A steam boiler of volume 2.3 m3 initially contained 1.7 m3 liquid water in equilibrium with 0.6 m3 of vapour at 100 kPa. The boiler is heated keeping the inlet and discharge valves closed. The relief valve is set to lift when the pressure in the boiler reaches 5500 kPa. Determine the amount of heat supplied to the contents in the boiler before the relief valve lifts.
Determine the quantity (volume) of saline water in a steam generator. The heat energy of 1539 kJ is supplied to saline water in the steam generator to heat from 21ºC to 104ºC for the generation of water vapor, Take the density & specific heat of the solution as 1022 kg/m3 & 4.8 J/kgºK respectively. Solution: Change in Temperature (in K) Answer for part 1 Mass of the saltwater (in kg)Answer for part 2 Quantity (Volume) of saltwater (in m3) Answer for part 3
A heat-insulated (adiabatic) constant volume vessel divided by a metal curtain. The volume of the compartments is not equal!. Initially, one of the chambers contains 2.5 kg of compressed s-phase water at a temperature of 60 °C and a pressure of 600 kPa. The other chamber is empty (vacuum). Then the metal curtain is lifted and the water covers the entire volume. Since the final pressure is 10 kPa, calculate the volume of the container and the final temperature of the water
Steam generators are a type of heat exchanges that are used in power plants to generate steam at desired pressure and temperature (Fig. Q1.b). In a steam generator, saturated liquid water at 30°C enters a 60-mm diameter tube at the volume flow rate of 12 L/s. After exchanging heat with hot gas, the water changes to steam and leaves the generator at a pressure of 9 MPa and a temperature of 400°C. During this process, the diameter of the water/steam tube does not change.(ii) What is the inlet velocity of the steam?
Consider the heating of water in a pan on a top of a range. If 24 kJ of heat is transferred to the water from heating element and 6 kJ of it is lost from the water to the surrounding air. Determine;(a) the net heat transfer to the water,(b) the efficiency for boiling water.
An electric water heater has a capacity of 2 liters. In this heater, the water is initially found as a saturated liquid at 150 kPa. When the water is in this state, the heater automatically turns on and heats the water, which expands at a constant pressure through a movable cover mechanism at the top of the heater, which has an associated work done by the system (Ws). Additionally, the electrical resistance supplies 2.2 MJ to the water. These types of heaters have very good thermal insulation and the surroundings are at normal conditions (25°C and 100 kPa). Based on this information: a) Determine the states of the working substance. b) Determine the minimum work (Wmin) with which the process can be carried out. c) Determine the exergy destroyed during this process.
60-Ton water-cooled air-conditioning system with a condensing temperature of 45°C and evaporating temperature of 0°C uses refrigerant 22. The overall heat transfer coefficient of 45 watts per m2 per K for the cooling coil, evaporator, and water-cooled condenser, determines the enthalpy at the entrance of the compressor in kJ/kg.
Steam in the condenser of a power plant is to be condensed at a temperature of 30°C with cooling water from a nearby lake, which enters the tubes of the condenser at 14°C and leaves at 22°C. The surface area of the tubes is 45 m2, and the overall heat transfer coefficient is 2100 W/m2?K. Determine the mass flow rate of the cooling water needed and the rate of condensation of the steam in the condenser.
Water vapour at 100 kPa and 150 is contained in a rigid vessel. At what temperature will the vapour stat to condense when the container is cooled slowly? How much heat will have to be removed per kilogram in this cooling process? Ans:95.68C, -81.4kj/kg